Extron Electronics FOX 500 DVI Tx User Guide - Manual (Page 12)

FOX 500 Tx/Rx • Installation
Installation, cont’d
2-6 FOX 500 Tx/Rx • Installation 2-7
a . Mark the location of the brackets relative to the screws.
b . Remove the transmitter or receiver from inside the
furniture.
c . Tighten the screws.
d . Replace the unit inside the surface (step 6).
Connections
Transmitter rear panel connections and settings
All connectors except the Configuration port are on the rear
panel (figure 2-4).
FOX 500 Tx
100-240V 0.3A 50/60 Hz
AUDIO INPUTS
INPUT LOOP THRU RGB INPUT
R G B
H/HV V
OR L R
RS-232 OVER FIBER
Tx Rx NA
REMOTE RS-232 ALARM
OPTICAL
1 2*
* OPTIONAL FOR RETURN DATA
LINK LINK
Tx Rx 1 2 RGB
FOX 500 DVI Tx
100-240V 0.3A 50/60 Hz
AUDIO INPUTS
L R
RS-232 OVER FIBER
Tx Rx NA
REMOTE RS-232 ALARM
OPTICAL
1 2*
* OPTIONAL FOR RETURN DATA
LINK LINK
Tx Rx 1 2
DDC
RESOL DVI - D INPUT LOOP - THRU
2
10 11 8
7
9
1 6
10 5 3 4 11 8
7
9 6
Figure 2-4 — FOX 500 Tx
transmitter’s connectors
N Connect an active
input to only the
BNC connectors
or the 15-pin HD
connector, not
both.
a RGB Input connectors
(FOX 500 [RGB] only) —
BNC connectors — Connect
an RGBHV, RGBS, RGsB, or
RsGsBs video source to these
BNC connectors. Connect the
cables as shown at right.
15-pin HD connector — Connect an analog VGA - UXGA RGB
video source to this 15-pin HD female connector.
b
Buffered Loop-through connector (FOX 500 [RGB] only) —
If desired, connect a local monitor to this 15-pin HD connector.
c
DVI-I Input connector (FOX 500 DVI only) — Connect a single
link of DVI-D to this DVI-I connector. See "DVI connector
(FOX 500 DVI)" on page 2-15
for pin assignments.
N The FOX 500 DVI accepts only the digital signals on
the DVI-I Input connector. The analog pins on the
port are not connected.
d
DDC Resol (ution) rotary switch (FOX 500 DVI only) — Set
this switch to one of the positions below to select the source of
the DDC or a specific resolution.
• Position 0 — The loop-through monitor (item
e , below)
is the source of the Display Data Channel (DDC)
• Position 1 — The DDC is selected either from the front
panel (using the menu system) or via one of the system's
serial ports (using an SIS command or the Windows-
based control program).
• Position 2 - F — Specify a resolution. The table below
identifies the switch positions and the associated
resolutions. The vertical refresh rate for all resolutions is
60 Hz with the exception of the 576p resolution, which is
50 Hz.
Pos. Pos. Pos.
Source or
Resolution Resolution Resolution
0 Local monitor 1280 x 1024 576p
1 RS-232/menu 1365 x 768 720p
2 1920 x 1200 1366 x 768 1080i
3 800 x 600 1400 x 1050 1080p
4
6
7
8
9
A
C
D
E
F
1024 x 768 1600 x 1200
5 B 1280 x 768 480p
e
Buffered Loop-through connector (FOX 500 DVI only) —
If desired, connect a local monitor to this DVI-I connector.
See "DVI connector (FOX 500 DVI)" on page 2-15
for pin
assignments.
R
RGBHV
G B
H /HV V
RGBS
RGsB,
RsGsBs
R G B
H/ HV V
R G B
H/HV V