GE Industrial Solutions EntelliPro ES - Manual (Page 248)

CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
1 6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
1 6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
1 6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
EPOS MOTOR MANAGEMENT SYSTEM – INSTRUCTION MANUAL
6.13
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
1 6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
1 6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
Star Delta,
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
OTE
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
Star Delta,
valve and Actuator.
EPOS MOTOR MANAGEMENT SYSTEM – INSTRUCTION MANUAL 6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
1 6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
1 6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
1 6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
1 6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
N
OTE
:
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
r
Star Delta,
valve and Actuator.
6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.5 EntelliPro CP5 Main panel
NOTE: If the drive typical is set to “Fully free logic”, the Modbus data interface of the free logic must follow the EntelliPro ES
standard, otherwise the data in the EntelliPro CP application might be incorrect.
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
Star delta reverse, Soft starter, Soft starter reverse, Dahlander, Pole changing starter, Solenoid valve and Actuator.
Next two figure show the Entellipro CP5 main panel.
1 6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
The EntelliPro CP5 device is a local touch control display inside the Motor Control Center (MCC) for control, alarm handling and
The EntelliPro CP5 application is created for the handling of the pre-programmed drive typical, like DOL,Reverse, Star delta,
visualize status, values and parameter settings. The functionality to parameterize the EntelliPro ES device is not included.
standa
Star Delta,
EPOS MOTOR MANAGEMENT SYSTEM – INSTRUCTION MANUAL 6.1
CHAPTER 6: ENTELLIPRO CP3 and CP5 APPLICATION
6.6 EntelliPro CP5 application setting
1 6.1
APPLICATION
The application setting menu, shown in the figure below can be accessed by pressing function key “F4” from root menu.
OTE
:
standa
r
Star Delta,
valve and Actuator.