Toshiba XLTR-200 - Manual (Page 86)

85
13.7.12 Communication Setting Parameters
Parameter Function / Title Bank Mask Adjustment Range Multiplier
0204 INVERTER ID NUMBER 1 00FF 0000 ∼ 00FF (0 ∼ 255) 1
0205 COMMUNICATION
SELECTION
1 0007 0000: OFF (0)
0001: RS485 (1)
0002: Modbus, F10, DeviceNet (2)
0003: TOSLINE S-20
(3)
0004: 12 bit binary input (4)
0005: 3-digit BCD (0.1Hz) (5)
0006: 3-digit BCD (1Hz) (6)

0206 MASTER/SLAVE
SELECTION
1 0018 0000: Slave (0)
0008: Master (freq. command) (1)
0010: Master (output frequency) (2)

0207
1
RS485 BAUD RATE 1 0004 0000: Normal mode (0)
0004: High-speed mode (1)

0208 TOSLINE-F10
COMMAND INPUT
1 0003 0000: OFF (0)
0001: Frequency command (1)
0002: Command input (2)
0003: Both (1) and (2) (3)

0209 TOSLINE-F10
MONITOR OUTPUT
1 003C 0000: (0) 0020: (8)
0004: (1) 0024: (9)
0008: (2) 0028: (10)
000C: (3) 002C: (11)
0010: (4) 0030: (12)
0014: (5) 0034: (13)
0018: (6) 0038: (14)
001C: (7) 003C: (15 )

020A
2
TOSLINE-F10 COMM
ERROR MODE
1 0080 0000: Data cleared (0)
0080: Data retained (1)

020B TOSLINE-S20
RECEIVE ADDRESS
1 FFFF 0000 ∼ 03FF (0 ∼ 1023) 1
020C TOSLINE-S20
TRANSMIT ADDRESS
1 FFFF 0000 ∼ 03FF (0 ∼ 1023) 1
020D TOSLINE-S20
COMMAND INPUT
1 001F 0000 ∼ 001F (0 ∼ 31) 1
020E TOSLINE-S20
MONITOR OUTPUT
1 001F 0000 ∼ 001F (0 ∼ 31) 1
020F TOSLINE-S20 FREQ
REF ADDR SELECT
1 0001 0000: Disable (0)
0001: Enable (1)
1
0210
1
TOSLINE-S20
FREQ REFERENCE
ADDR
1 FFFF 0000 ∼ 03FF (0 ∼ 1023) 1
0211 TOSLINE-S20 COMM
ERROR MODE
1 0002 0000: Data cleared (0)
0002: Data retained (1)
1
0212
3
TOSLINE-S20 COMM
OPTION RESET
1 0004 0000: No effect (0)
0004: Reset (1)
1
0213 RS485/12-BIT BINARY
BIAS,GAIN
0 / 1 0020 0000: OFF (0)
0020: ON (1)

0214 RS485/12-BIT
BINARY POINT #1
0 / 1 00FF 0000 ∼ 0064 (0 ∼ 100) 1
0215 RS485/12-BIT
BINARY PT. #1 FREQ
0 / 1 FFFF 0000 ∼ Fmax (0 ∼ Fmax) 0.01
0216 RS485/12-BIT
BINARY POINT #2
0 / 1 00FF 0000 ∼ 0064 (0 ∼ 100) 1
0217
1
RS485/12-BIT
BINARY PT. #2 FREQ
0 / 1 FFFF 0000 ∼ Fmax (0 ∼ Fmax) 0.01