Microphone control (u.s.a./ canada only) – Kenwood TM-G707 User Manual
Page 66
60
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
MICROPHONE CONTROL (U.S.A./ CANADA ONLY)
You can change numerous transceiver settings by using
the MC-53DM microphone keys. DTMF tones are used
for this remote control operation. First switch
Microphone Control ON using Menu Set-up.
Note:
◆
Audible DTMF tones from other transceivers near you may be picked
up by your MC-53DM microphone. If so, this could prevent the
function from working correctly.
◆
U.S.A. only:
It is illegal to transmit control codes on the VHF band.
Transmit control codes only on the UHF band.
1
Press [MNU] to enter Menu mode.
2
Select Menu No. 27 (MC.RM).
3
Press [OK], then turn the Tuning control to switch the
function ON (or OFF).
4
Press [OK] again to complete the setting and exit
Menu mode.
The following table shows what function is switched ON
and OFF or which setting is changed. For the shaded
items, press [D] first (ex. [D], then [2]).
1
Transceivers equipped with the optional VS-3 unit announce
the displayed information {page 63}.
2
After entering the selection mode, press [ ] or [#] to change
the level or selection.
3
Both Volume Change and Squelch Adjustment cannot be
activated at the same time.
4
Both Volume Change and Squelch Adjustment must be OFF
to change the tone or frequency step using this key.
5
First press [2] to activate the Tone or CTCSS function.
6
Press [OK] on the front panel of the transceiver to complete
the setting.
y
e
K
n
o
i
t
c
n
u
F
y
e
K
n
o
i
t
c
n
u
F
1
n
a
c
S
y
t
i
r
o
i
r
P
B
e
g
n
a
h
C
l
e
v
e
L
r
e
m
m
i
D
2
S
S
C
T
C
/
e
n
o
T
C
—
3
e
s
r
e
v
e
R
D
]
F
[
y
e
k
4
e
g
n
a
h
C
p
e
t
S
z
H
M
1
n
w
o
D
4
5
r
o
t
i
n
o
M
p
U
4
6
t
u
o
d
a
e
R
y
c
n
e
u
q
e
r
F
s
p
e
e
B
y
b
1
2
t
c
e
l
e
S
e
n
o
T
6
,
5
,
2
7
e
g
n
a
h
C
e
m
u
l
o
V
3
,
2
3
t
c
e
l
e
S
n
o
i
t
c
e
r
i
D
t
e
s
f
f
O
8
n
o
i
t
a
r
e
p
O
d
n
a
b
-
s
s
o
r
C
5
k
c
o
L
d
a
p
y
e
K
F
M
T
D
9
t
n
e
m
t
s
u
j
d
A
h
c
l
e
u
q
S
3
,
2
6
k
c
o
l
n
U
d
a
p
y
e
K
F
M
T
D
0
e
g
n
a
h
C
r
e
w
o
P
X
T
0
p
e
t
S
y
c
n
e
u
q
e
r
F
e
g
n
a
h
C
6
,
2
A
r
e
t
n
E
B
P
I
A