Sony E 16mm f/2.8 Lens - Manual (Page 23)

23
SR Live Auto  On: Automatically sets a group of
items required for conversion
settings from HDR signal to SDR
signal of "EOTF," "Color Space,"
"Transfer Matrix" and "Conv.
Preset."
When SR Live Metadata is
superimposed on the input SDI
signal, the settings are
configured based on the HDR
SDR Relation Table (a group of
items that need to be set to
generate an SDR signal from
the HDR signal).
For items where SR Live
Metadata is not superimposed
or is invalid, the setting values
of the corresponding items in
the conversion preset data will
be applied.
When OETF of HDR SDR
Relation Table is S-Log3, "EOTF"
is automatically set to "S-
Log3(Live HDR)."
When both "SR Live Auto" and
"VPID/HDMI Auto" are "On," the
HDR SDR Relation Table
information of "SR Live Auto"
takes precedence over the
settings of "EOTF," "Color
Space" (Color Gamut) and
"Transfer Matrix."
 Off: When "VPID/HDMI Auto" is
"On," the setting conditions are
followed. When "VPID/HDMI
Auto" is "Off," the values set in
"EOTF," "Color Space," "Transfer
Matrix" and "Conv. Preset" are
used for a group of items
required for the HDR signal to
SDR signal conversion settings.
Note
When "VPID/HDMI Auto" and "SR Live
Auto" are "On", the settings of this unit
may be changed due to changes in
Metadata, and the video may be
interrupted during the settings. To
avoid this, set to "Off". (PVM-X2400/
X1800 only)
Submenu Setting
RGB/YCC Range Select from the following when “VPID/
HDMI Auto” is set to “Off” and the RGB
signal or YCbCr signal is input.
 Full: 0 to 255 (8bit) / 0 to 1023 (10bit)
/ 0 to 4095 (12bit)
 Limited: 16 to 235 (R/G/B/Y), 16 to
240 (Cb/Cr) (8bit) / 64 to 940
(R/G/B/Y), 64 to 960 (Cb/Cr)
(10bit) / 256 to 3760 (R/G/B/Y),
256 to 3840 (Cb/Cr) (12bit)
 SDI Full 1) : 4 to 1019 (10bit) / 16 to
4076 (12bit)
1) Available only when SDI input is
selected. This manual regards the
Full Range signals that are scaled to
the quantized value except the
inhibit code on the SDI standard as
the SDI Full Range.
EOTF Select the gamma from the following
when “VPID/HDMI Auto” is set to “Off.”
 2.2
 2.4
 2.6
 2.4(HDR)
 S-Log3
 SMPTE ST 2084
 ITU-R BT.2100(HLG)
 S-Log3(Live HDR) 1)
When “ITU-R BT.2100(HLG)” is selected
 System Gamma: Sets the system
gamma of the HLG. Set from
1.000 to 1.500. (Default value:
1.200)
1) “S-Log3(Live HDR)” is the setting for
which this unit is used as the
monitor in the S-Log3 Live HDR
workflow which Sony advocates.
Displays the S-Log3 input signal
adding the system gamma. This
system gamma is set so that the
compatibility with the monitoring of
the conventional (SDR) environment
is valued and you can perform
suitable picture expression without
discomfort when adjusting the
picture of the HDR camera. For
details on S-Log3 Live HDR
workflow which Sony advocates,
refer to the description of What’s
HDR and the Live HDR workflow on
the Sony website.
Submenu Setting