Yaskawa F7 to A1000 - Manual (Page 53)

10 Appendix 2 Parameter Cross Reference
YASKAWA PL.A1000.02 F7 to A1000 - Product Transition Guide 53
Hardware
Protection
Overheat Pre-
Alarm Operation
Selection
L8-03 3 L8-03 3
L8-03 L8-03
0: Ramp to stop 0: Ramp to stop
1: Coast to stop 1: Coast to stop
2: Fast Stop 2: Fast Stop
3: Alarm Only 3: Continue operation (Alarm triggered)
— 4: Continue operation at reduced speed as set in L8-19
Input Phase Loss
Protection
Selection
L8-05 0 L8-05 1
L8-05 L8-05
0: Disabled 0: Disabled
1: Enabled 1: Enabled
Output Open-
Phase Protection
Selection
L8-07 0 L8-07 1
L8-07 L8-07
0: Disabled 0: Disabled
1: Enabled (triggered by a
single phase loss)
1: Enabled (triggered by a single phase loss)
2: Enabled (triggered
when two phases are lost)
2: Enabled (triggered when two phases are lost)
Output Ground
Fault Detection
Selection
L8-09 1 L8-09 1*
L8-09 L8-09
0: Disabled 0: Disabled
1: Enabled 1: Enabled
*Determined by parameters C6-01 and o2-04
Heatsink Cooling
Fan Operation
Selection
L8-10 0 L8-10 0
L8-10 L8-10
0: During run only 0: During run only
1: Fan always on 1: Fan always on
Heatsink Cooling
Fan Operation
Delay Time
L8-11 60 s L8-11 60 s —
Ambient
Temperature
Setting
L8-12 45°C L8-12 40°C Set the ambient temperature where the drive is being used.
oL2 Characteristics
Selection at Low
Speeds
L8-15 1 L8-15 1
L8-15 L8-15
0: Disabled 0: Disabled
1: Enabled 1: Enabled
Soft CLA
Selection
L8-18 1 L8-18 1
L8-18 L8-18
0: Disabled 0: Disabled
1: Enabled 1: Enabled
Hunting
Prevention
Function
Hunting
Prevention
Function Selection
n1-01 1 n1-01 1
n1-01 n1-01
0: Disabled 0: Disabled
1: Enabled 1: Enabled
Hunting
Prevention Gain
Setting
n1-02 1.00 n1-02 1.00 —
Speed Feedback
Detection Control
Function
Speed Feedback
Detection Control
(AFR) Gain
n2-01 1.00 n2-01 1.00 —
Speed Feedback
Detection Control
(AFR) Time
Constant
n2-02 50 ms n2-02 50 ms —
Speed Feedback
Detection Control
(AFR) Time
Constant 2
n2-03 750 ms n2-03 750 ms —
High slip Braking
High-Slip Braking
Deceleration
Frequency Width
n3-01 5 % n3-01 5 % —
High-Slip Braking
Current Limit
n3-02 150 % n3-02 150 % * *Upper limit is determined by L8-38 and C6-01
High-Slip Braking
Dwell Time at Stop
n3-03 1.0 s n3-03 1.0 s —
High-Slip Braking
Overload Time
n3-04 40 s n3-04 40 s —
Feed Forward
Control
Feed Forward
Control Selection
— — n5-01 0 New for the A1000.
Motor
Acceleration Time
--- — n5-02 *
*Determined by C6-01, o2-04, and E5-01.
New for the A1000.
Feed Forward
Control Ratio Gain
— — n5-03 1.00 New for the A1000.
Parameter Name
F7 A1000 Setting
Parameter Default Parameter Default F7 A1000