Denon AVR-4306 - Manual (Page 73)

68
Advanced Setup – Part 1 Advanced Setup – Part 1
SW Level:
Sets the playback level of the analog signal that was input to
the EXT. IN subwoofer terminal.
Select according to the specifications of the player being
used. Also refer to the player’s operating instructions.
+15dB (default) recommended. (0, +5, +10 and +15 can be
selected.)
3 Press the CURSOR H H button to select “iPod
Dock”, then press the CURSOR D D or H H button to
select “NotUsed” or “Used” and press the ENTER
button.
Example: When “CD” is selected for “iPod Function” and
“iPod Dock” is set to “Used”
Setting the Input Function Level
• Correct the playback level of the different input sources.
• Adjust the playback levels of the devices connected to the
different input sources to the same level to eliminate the need
for adjusting the main volume each time the input source is
switched.
1 Press the CURSOR D D or H H button to select
“Input Function Lev.” at the “Audio Input
Setup” menu, then press the
ENTER button.
• The “Input Function Lev.” screen appears.
3
Press the ENTER button to enter the setting.
• The “Audio Input Setup” menu reappears.
2 Press the CURSOR D D or H H button to select the
input source, then press the CURSOR F F or G G
button to adjust the level.
The level can be adjusted between –12 dB and +12 dB in
units of 1 dB.
When “Yes” is selected for “Default”, the settings are
automatically reset to the default values.
• After completing this setting, check that the playback levels for
the different sources are the same.
Setting the iPod Assignment
When connecting the iPod via a iPod Dock, it is possible to assign
the iPod Dock’s audio and video signals to any input terminals on
the AVR-4306 and play them.
1 Press the CURSOR D D or H H button to select “iPod
Assign” at the “Audio Input Setup” menu, then
press the
ENTER button.
• The “iPod Assign” screen appears.
3
Press the ENTER button to enter the setting.
• The “Audio Input Setup” menu reappears.
2 Press the CURSOR F F or G G button to select the
input function to be assigned, then press the
ENTER button.
• When “AUX” is assigned to “iPod Function”, the mode
switches between “AUX/Net” and “AUX/iPod” each time the
AUX button is pressed.
• When a function other than “AUX” is assigned to “iPod
Function” and “iPod Dock” is set to “NotUsed”, remote
control operation is possible using the remote control codes of
the assigned function.
Surr. Sp:
Presets the surround speakers that are used in the EXT. IN
mode. Select according to the specifications of the player
being used. Also refer to the player’s operating instructions.
• Surr. A:
Select when using surround speakers A.
• Surr. B:
Select when using surround speakers B.
• Surr. A+B:
Select when using both surround speakers A and B.
Aux:
This is the factory default setting.
Connection using a iPod Dock is not possible.
CD, CDR/TAPE:
When using a iPod Dock, it is possible to connect with the
audio input terminal of the assigned function.
NotUsed:
This is the factory default setting. Select this when not using
a iPod Dock.
Connect the iPod cable directly to the iPod.
Used:
Select this when using a iPod Dock.
Connect the iPod Dock’s audio and video output connectors
to the audio and video input terminals of the function set at
“iPod Function”.
DVD, VDP, DBS, TV, VCR-1, VCR-2, V.Aux:
When using a iPod Dock, it is possible to connect with the
audio and video input terminals of the assigned function.
iPod
AVR-4306
“Aux1” is setting of “AUX/Net”, and “Aux2” is setting of
“AUX/iPod”.