Daktronics 2000 Rodeo OmniSport - Manual (Page 67)

DD2870296
Rev 0 27 August 2014
Page 1 of 2 201 Daktronics Drive PO Box 5128, Brookings, SD 57006-5128
Tel: 1-800-DAKTRONICS (1-800-325-8766) Fax: 605-697-4700
Web: www.daktronics.com/support
Rodeo Keys

COPY NOW UP TO LEADER copies Now Up number on the scoreboard to the leader position.

LEADER TIME/SCORE sets the time or score for the leader, depending on the current console mode of operation.

LEADER NUMBER sets the number of the current leader shown on the scoreboard.

BUBBLE TIME/SCORE sets the bubble time or score, depending on the current console mode of operation.
 CLEAR NOW UP clears the Now Up competitor on the scoreboard.
 NOW UP TIME/SCORE sets the time or score for the Now Up competitor, depending on the current console mode of operation.
 NOW UP NUMBER sets the number of the current Now Up competitor shown on the scoreboard.

CATTLE NUMBER is used for team penning.

CLEAR DISPLAY clears all data on the scoreboard.

PENALTY sets the penalty time for the current competitor. A second press of the penalty key turns the penalty off.

RERIDE toggles the reride captions on or off.

# OF JUDGES sets the number of judges used in scored events.

EDIT JUDGES SCORES is used to enter or edit the judge's scores.

ACCEPT JUDGES SCORES totals the judges’ scores and displays the score on the scoreboard.

ENABLE JUDGE CONSOLES is used to re- enable the judges’ consoles after the scores have been accepted.
 CLEAR PREVIOUS clears out the previous competitor number and time/score.
 RESET JUDGES clears all judges' scores.

SCORED EVENTS selects the Scored Events mode of operation (bull riding, bareback, etc.).

AUTO TIMING selects the Automatic (photocell) mode of operation (barrel racing).

1 TIMER, 2 TIMERS, 3 TIMERS select the manual timing with one, two or three timers, respectively
(steer wrestling, team roping, etc.).
 CUTTING selects the Cutting mode of operation.
 NO TIME – NO SCORE displays “no time” or “no score” on the scoreboard and printout.

SET TIMER 1/PHOTOCELL sets the Timer 1 time or Photocell time, depending on the current console mode of operation.

SET TIMER 2, SET TIMER 3 sets the Timer 2 or Timer 3 time (if applicable).

ENABLE/DISABLE PHOTOCELL enables or disables photocell input.
[1] SCBD MENU
[11] SCBD ON/OFF
[12] SCORE DISPLAY
[13] DIMMING
[2] PRINT MENU
[21] LOGGING
[22] INTENSITY
[3] SETUP MENU
[31] TIMER
[311] TIMER PREC
[312] TIMER MODE
[313] BEEPER
[314] BEEP VOLUME
[315] HALF POINTS
[316] HORN
[317] JUDGE START
[32] PHOTOCELL
[321] PCELL PREC
[322] PCELL ARMING
[323] PCELL SWITCH
[33] NETWORK
[331] NETWORK ENABLE
[332] MAC ADDRESS
[333] IP ADDRESS
[334] SUBNET MASK
[335] GATEWAY ADDRES
[336] SOCKET NUMBER
[4] TEST MENU
[41] BATTERY
[42] SCOREBOARD
[421] CYCLE ON/OFF
OmniSport 2000 Rodeo Menu Navigation
Two methods for navigating through the OmniSport 2000 menus:
The first method allows you to step through each of the menu levels. To use this method, press [
MENU ] and then use [], [], [], and
[] to scroll through the menus. Press [ ENTER ] to select the menu displayed on the LCD.
The second method is to go directly to a menu. Press [
MENU ] followed by the one to three digit number from the list below and the LCD
will prompt you for the desired setting or action in that menu. For example, “322” will prompt you to enter the photocell arming delay.
After you are done navigating through the menus, press [
MENU ] to return to the main menu.