Futaba 10C 2.4GHz User Manual

Page 42

'XDOWULSOHUDWHVDQGH[SRQHQWLDOD/R,EXP): assigns adjusted rates and exponential.

Dual/Triple Rates:

UHGXFHLQFUHDVH WKH VHUYR WUDYHO E\ IOLSSLQJ D VZLWFK RU

(ACRO

GLID) they can be engaged by any stick position. Dual rates affect the

control listed, such as aileron, not just a single (ex: channel 1) servo. For
example, adjusting aileron dual rate will affect both aileron servos when using
FLAPERON

or AIL-DIF, and both aileron and elevator servos’ travel when using

AILEVATOR

or ELEVON or a CCPM helicopter.

Activation:
• Any SWITCH, A-H. If you choose a 3-position switch, then that dual rate instantly becomes a triple rate (see example).
• The glider programming offers you the choice of Cond. This option allows you to have a separate rate for each of

condition. (GLID)

• Stick position (ACRO

GLID ([ 2Q UXGGHU \RX QRUPDOO\ XVH RQO\ WKH FHQWHU RI WKH VWLFN PRYHPHQW H[FHSW IRU

H[WUHPH PDQHXYHUV VXFK DV VQDSVVSLQVVWDOOV$V ORQJ DV \RXU 58''(5 67,&. GRHV QRW H[FHHG RI PD[LPXP
throw, the rudder responds at your lower rate, allowing small, gentle corrections. When the stick passes 90% (ie. stall
turn), the rudder goes to high rate’s 90%, which is a MUCH higher amount of travel than your low rate at 89%.)

Ex: (At 100% = 1”)

Low Rate = 50%

High Rate = 100%

At 89%

Low Rate = .45”

At 90%

High Rate = .9”

[Note] Only if any stick is chosen by the item of "SW1", a switch can also be chosen by the item of "SW2." When operated
simultaneously, the switch operation has priority over the stick operation. (ACRO)

Adjustability:
• Range: 0 - 140% (0 setting would deactivate the control completely.) Initial

value=100%

• Adjustable for each direction (ACRO

GLIDLH8SGRZQOHIWULJKW([0RVW

PRGHOVÀ\XSULJKWZLWKRXWDQ\HOHYDWRUWULPEXWUHTXLUHVRPHGRZQHOHYDWRU
ZKHQLQYHUWHGMXVWWRPDLQWDLQOHYHOÀLJKW%\LQFUHDVLQJWKHGRZQWUDYHOE\
the amount required to hold the model inverted, the model now has equal
travel available from level upright or level inverted.)

Exponential:

FKDQJHVWKHUHVSRQVHFXUYHRIWKHVHUYRVUHODWLYHWRWKHVWLFNSRVLWLRQWRPDNHÀ\LQJPRUHSOHDVDQW

make the servo movement less or more sensitive around neutral for rudder, aileron, elevator, and throttle (except HELI type
- use THROTTLE CURVE instead). (ACRO type—throttle EXP and THROTTLE CURVE can not be activated simultaneously.
Why use expo? Many models require a large amount of travel to perform their best tricks. However, without exponential,
WKH\DUH³WRXFK\´DURXQGQHXWUDOPDNLQJWKHPXQSOHDVDQWWRÀ\DQGPDNLQJVPDOOFRUUHFWLRQVYHU\GLI¿FXOW$GGLWLRQDOO\
by setting different exponentials for each rate, you can make the effectiveness of small corrections similar in each rate, as
in our example below.

The best way to understand exponential is to try it:
• Having made no changes yet in the D/R,EXP screen, move SWITCH D to “down” (toward the AILERON STICK).
• Cursor down to EXP and dial to +100%.
• Move SWITCH D up. Hold the AILERON STICK

DWVWLFNDQGPRYHSWITCH D down.

• Notice how much less travel there is.
*RWRVWLFNDQGUHSHDW1RWLFHKRZWKHWUDYHOLVPXFKFORVHULIQRWLGHQWLFDO

High Rate

Low Rate

100%

30%

90%