Futaba 10C 2.4GHz User Manual

Page 30

$/22.$77+(5$',26)81&7,21667(3%<67(3

MODEL

submenu: includes three functions that manage model memory: MODEL SELECT, MODELCOPY and MODELNAME. Since

these functions are all related, and are all basic features used with most models, they are together in the MODEL submenu of
the BASIC menu.

NOTE: When you choose a new model in the MODEL SELECT function, if the new
model is set to the other modulation, you must cycle the transmitter power to change
PRGXODWLRQV,I\RXGRQRWF\FOHWKHSRZHUWKHPRGXODWLRQW\SHZLOOÀDVKRQWKHKRPH
screen to remind you. You are still transmitting on the other modulation until you
affect this change.

GOAL:

STEPS:

INPUTS:

Select Model #3.

N O T E : T h i s i s o n e o f s e v e r a l
functions for which the radio requires
FRQ¿UPDWLRQWRPDNHDFKDQJH

Open BASIC menu, then open MODEL
submenu.

for 1 second.

(If ADVANCE,

again.)

if required to MODEL.

Choose Model #3.

to 3.

&RQ¿UP\RXUFKDQJH

for 1 second.

Are you sure?

displays.

Close.

Confirm proper modulation of new
model memory.

If PPM, PCM or 2.4G

DUH ÀDVKLQJ LQ WKH XSSHU ULJKW KDQG FRUQHU WKHQ WKH QHZ

PRGHOLVVHWIRUWKHRWKHUUHFHLYHUW\SH7XUQWKHWUDQVPLWWHURIIRQWRFKDQJHWKH
modulation.

Where next?

NAME

the model: see p. 32.

Change MODEL TYPE (aircraft, heli, glider): see p. 34.
Change modulation [FM (PPM

PCM or 2.4G-10CH7CH]: see p. 35.

Utilize servo REVERSE: see p. 38.
Adjust END POINTs: see p. 39.
Set up IDLE-DOWN and THR-CUT for throttle management: see p. 40, 41.

MODEL SELECT

: This function selects which of the 15 model memories in the

WUDQVPLWWHU RU LQ WKH RSWLRQDO CAMPac-... WR VHW XS RU
À\)RUFODULW\WKHPRGHOVQDPHDQGDQLPDJHRILWVW\SHDUHLQGLFDWHGDIWHULWV
number. (Each model memory may be a different model type from the other
memories.)

T9C/T9CS CAMPac data conversion

Although a CAMPac

GDWD ZKLFK VDYHG WKH GDWD RI D FRQYHQWLRQDO 7&7&6 WUDQVPLWWHU

cannot be used calling directly, it is possible to use it by the following method, copying to
the model memories of a T10C transmitter. When using the CAMPac, it will be displayed,
for example as "01<-Pac 01." Press DIAL for 1 second in this state and the check display of
"Are you sure?" will appear. Press DIAL again, the data of CAMPac will be copied to model

number"01" of the T10C transmitter. As for the data of a function added by T10C, an initial value is set up at this time.
3OHDVHGRQRWIRUJHWWKHFKHFNRIVHWWLQJGDWDEHIRUHDÀLJKW
In addition, refer to p.17 for the initializing method of the CAMPac.

Note: If you are using the optional CAMPac-16K, your choices in MODEL SELECT and MODEL COPY will include 16-19,
which are the model memories in the CAMPac. You do not have to COPY from the CAMPac to the transmitter prior to
working with that model

ÀDVKLQJ