Panasonic CF-M32 Series User Manual
Operating instructions cf-m32 series, Personal computer
Table of contents
Document Outline
- Customer's Record
- Introduction
- Illustrations in this Manual
- Copyright
- Disclaimer
- Trademarks
- Federal Communications Commission Radio Frequency Interference Statement
- Lithium Battery!
- Read Me First
- Names of Parts
- starting Up/Shutting Down
- Creating Backup Disks
- Computing On The Road
- Four Important Points
- Conserving Power
- Things to Remember
- ( Leave your computer off when it is not in use (cépage 18) P Adjust the brightness (dark) with(^+(F2| (cépage so)
- > Before stepping away from your computer, press ^n\+ [FIO] to put your computer in the standby mode(a=page 81)
- In the power management mode, the setting of [Power Saving] is recommended (cépage 26)
- Enter the following settings under [Operation Setting] in [Panasonic Power Management] (cépage 26)
- NOTE>
- Computing On The Road
- Computing On The Road
- Using the Battery Pack
- Precautions
- Using the Battery Pack
- Using the Battery Pack
- Accurately Displaying Battery Capacity
- When you do not want your computer to be used without permission
- When the user password is set
- 1 Run the Setup Utility (c^ page 73)
- 2 Using Q and QJ , select [System Setup] then press
- [Enter]
- 3 Using Q and Q , select [User Password], then press [Enterl
- ^ # To enable or change your password
- #To disable your password
- 5 At the confirmation screen, press ¡Enter)
- S Press [escI to end the password setting procedure 7 Close the Setup Utility (q* page 74)
- Security Measures
- When you do not want your Supervisor Setup changed without permission
- I When the supervisor password is set in the setup utility (o-page 78),
- Setting the supervisor password (enabling, changing, disabling) 7 Run the Setup Utility (q> page 73)
- 2 Using Q and 0 , select [Supervisor Setup] then press
- [Enter]
- 3 Using Q and Q , select [Supervisor Password], then press (Enter]
- ^ # To enable or change your supervisor password
- #To disable your password
- 5 At the confirmation screen, press [Enter]
- 6 Press [Esc] to end the password setting procedure
- 7 Close the Setup Utility (c5= page 74)
- When you do not want your Supervisor Setup changed without permission
- Infrared Data Communications
- Add-ons/Peripherals
- Connecting/Disconnecting the Port Replicator
- ctWQ
- Port Replicator Attachment Diagram
- Using the External Floppy Disk Drive (FDD)
- Connecting/Disconnecting the External FDD
- Using PC Cards
- Installing/Removing the PC Card
- Adding Memory
- Installing/Removing the RAM Module 1 Power off your computer (o-page 18)
- 2 Disconnect your computer from the power outlet
- 3 Remove the battery pack (cépage 32)
- 4 Turn your computer over and use a screwdriver to remove the screw shown in the illustration
- 5 Open the display and remove the memory cover
- 6 9 Installing the RAM module
- 1 Removing the RAM module
- 7 Put the cover back into place, then close the display
- 8 Turn your computer over and use a screwdriver to fasten the screw
- Using an External Display
- 1 Power off your computer (a=page 18)
- 2 Connect the external display to your computer
- 3Turn on the display, then turn on your computer with the LCD panel opened
- 1 Run the Setup Utility (opage 73).
- 2 Using(i|andfî), select [System Setup], then press
- 3 Using QandQ, select [Video Setup], then press
- [Enterl
- 4 UsingfnandQ, select [Display], select the display with ¡then press[Esc]
- 5 Close the Setup Utility (cépage 74).
- 4Select your external display
- Using a Printer
- List of Error Codes
- Dealing With Problems
- Reinstalling Software
- LIMITED USE LICENSE AGREEMENT
- Setup Utility
- Key Combinations
- LED Indicators
- Index