Waterworks Classic 71" x 36 x 20" Right Hand Air and Whirlpool Bathtub with End Drain" - Manual (Page 6)

Classic Whirlpool Bathtub
TESTING SYSTEM OPERATION: WARNINGS:
➢ Remove all debris and residue before filling the tub with water.
➢ Fill the tub until the water level sensor button ( 1 ⁄ 2 " metal disc approx. 2"
above the jets) is covered. (Do not run pump without water in the tub.)
➢ Examine the tub and system carefully for leaks.
➢ Position the jets downward.Turn on system and allow the tub to run
approximately 2–3 minutes.
➢ Allow water to sit for 10 minutes and check for leaks.
➢ Reactivate the pump three additional times for 2–3 minute cycles to
ensure that the pump is priming properly.
➢ Open drain, empty tub, and wipe up excess water with a soft, damp sponge.
TECHNICAL SERVICE:
➢ Read the product identification tag (located on bathtub near pump).
This tag includes all pertinent information specific to your product,
including the model, size, date of manufacture, and ID number.
➢ Have information available when contacting Waterworks Product Support
at 1-800-927-2120 (8am –7pm EST).
OPERATING INSTRUCTIONS:
➢
Whirlpool motor: 120 volt / 20 amp GFCI protect dedicated line.
➢
In-liner motor: 120 volt / 20 amp GFCI protect dedicated line.
➢
To test the GFCI, do the following: (1) Plug power cord(s) into electrical
outlet (2) Push the test button; check that the power has been
interrupted, and (3) Push the reset button; check that the power has
been restored.
IF THE GFCI DOES NOT OPERATE PROPERLY DURING THE TEST,
THERE IS A GROUND CURRENT FLOWING, WHICH INDICATES
THE RISK OF ELECTRIC SHOCK.
DO NOT USE THE BATHTUB. DISCONNECT THE BATHTUB
IMMEDIATELY AND HAVE THE POWER SOURCE SERVICED BY
QUALIFIED PERSONNEL.
When power is applied, the electronic switch will require approximately 30
seconds to balance before it will operate correctly.
➢ Fill the tub with water until the water level sensor button ( 1 ⁄ 2 " metal disc
approx. 2" above jets) is covered. With the water level sensor submerged,
the on/off sensor (1" metal disc on tub deck) becomes operational.
➢ Touch the on/off sensor to start the pump.
➢ Touch the on/off sensor a second time to stop the pump.
The touch control may take 1 ⁄ 2 second between touches to operate properly.
If the water in the bathtub drops below the water level sensor at any time during
the whirlpool operation, the tub motor will instantly shut off all functions.
CLEAN-UP AFTER INSTALLATION:
➢
When cleaning up after installation, do not use abrasive cleaners as
they may scratch and dull the surface. Use warm water and a liquid
nonabrasive detergent to clean the surface.
➢
Stubborn stains, paint, or tar can be removed with turpentine or paint
thinner. Do not allow cleaners containing petroleum distillates to remain in
contact with the bath surface for long periods of time. Plaster can be
removed by scraping with a wood edge. Do not use metal scrapers, wire
brushes, or other metal tools. One of the powder-type detergents may be
used on a damp cloth to provide mild abrasive action to the residual plaster.
The following basic safety precautions should always be followed when
using your bathtub.
➢ CAREFULLY READ AND FOLLOW ALL INSTRUCTIONS BEFORE
ATTEMPTING TO OPERATE YOUR WHIRLPOOL BATHTUB.
➢
Caution should always be exercised when entering or leaving the bathtub.
➢ DANGER:
To reduce the risk of injury, do not permit children or persons
with a disability to use this unit unless they are closely supervised at all
times.
➢
This product is intended for indoor use only. Use the bathtub only for its
intended purpose and do not use attachments or accessories that are not
recommended by the manufacturer.
➢
Never drop or insert any objects into any openings.
➢
Due to the hazard of suction, persons with long hair should demonstrate
extra caution.
➢
Do not use the bathtub without the suction covers in place. Do not block
off the suction fittings.
➢
The bathtub must be connected to an electrical supply circuit that is
protected by a ground fault circuit interrupter (GFCI), which is provided
by the installer.The GFCI should be tested periodically to ensure that it
is working properly.
➢
Keep all electrical appliances, such as radios and hair driers, a safe distance
from the bathtub.
➢
Failure to comply with all instructions, requirements, and warnings con-
tained in this manual creates a serious hazard to the bathtub user and may
result in serious personal injury.
➢
Do not use the bathtub when sleepy or drowsy, under the influence of
alcohol or prescription medications, or when overheated. Pregnant women
and persons with medical conditions should consult their physicians for
advice before use.
Operating Instructions
W A T E R W O R K S