Waterworks Easton Vintage Exposed Tub Filler with Cross Handles and Handshower with White Porcelain Lever Diverter and White Porcelain Lever Handles - Manual

➢ Refer to the specification and assembly drawings attached.
Faucet is sold partially assembled but shown fully
disassembled for illustrative and service purposes only.
➢ Inspect this product to assure you have all parts required for
proper installation.
➢ Use only a strap wrench or protected/smooth-jaw wrench
on any finished surface.
➢ Install accessible hot and cold service stop valves to facilitate
servicing.
ROUGH IN:
1. Run
3 /
4
" hot and cold supply lines for maximum water flow.
The spread between supplies is 7- 1 /
4
" and is NOT adjustable.
2. Install a well supported 3 /
4
" sweat x 3 /
4
" female IPS elbow
onto each supply line.The distance from the face of the
elbow to the surface of the finished wall m
mu usstt b be e 1 1 //
2 2
"" ffo orr
o op pttiim mu um m p prro ojje eccttiio on n iin ntto o tth he e ttu ub b..
3. Verify the elbows are secure, level, at the proper spread of
7- 1 /
4
", and equal depths.
4. Stub-out 3 /
4
" capped nipples to allow for finished wall
installation and then turn on the supplies and check for leaks.
TUB FILLER INSTALLATION:
5. After the finished wall is complete, remove the nipples
installed in step 4.
6. Apply thread compound to the longer of the 2 threaded
sections of the wall union (2).
7. Thread the wall union into the 3 /
4
" elbow and tighten using a
17mm hex wrench.
8. Slide an escutcheon (3,4) onto the union. If desired, a bead
of caulk of silicone may be applied where the escutcheon
contacts the wall.
9. Install a 3 /
4
" washer (1) into each inlet and then attach the
tub filler to the wall unions by tightening the nuts (22) on
the back side of the tub filler.
10.Insert a 3 /
4
" washer (19) into the base of the cradle (11) and
then secure the cradle to the tub filler by tightening the nut
(11a). Cradle can be positioned with hose outlet pointing to
the left or the right.
Easton ® Exposed Tub Filler with wall unions
These guidelines have been prepared for the professional contractor to aid in the installation of:
EASTON
® EXPOSED TUB FILLER (EATU21,22-K,24-K,25-K,31,32-K,34-K,35-K)
EASTON ® WALL UNIONS (EATU18)
All dimensions are based on original specifications and are subject to change and variation.
Please consult your Design Associate for current specifications.
Installation Guidelines
1
W A T E R W O R K S ®
12/03
(Covered Escutcheon)
EATU21(White porcelain handles and indices) EATU18(Wall Unions)
EATU22-K(Metal handles and indices)
EATU24-K(Black porcelain handles and metal indices)
EATU25-K(Oak handles and metal indices)
7 1 / 4 "
6 3 /
4
" to 8"
1 1 /
4
"
max
4 1 /
2
"
5 3 /
8
"
9"
Notes:
•
3 /
4
" male NPT inlets
• Spread is NOT adjustable
• Check tub deck and tub measurements to assure
the spout projects far enough into the tub
• Anti scald protections is the responsibility of the
installer and according to applicable codes
• Replacement cartridge - part # WWPTU11
EATU21-25-K
(Uncovered Escutcheon)
EATU31(White porcelain handles and indices)
EATU32-K(Metal handles and indices)
EATU34-K(Black porcelain handles and metal indices)
EATU35-K(Oak handles and metal indices)
INSTALLATION GUIDELINES:
IMPORTANT:
➢
➢ T To o e en nssu urre e tth hiiss p prro od du ucctt iiss iin nssttaalllle ed d p prro op pe errllyy,, yyo ou u m mu usstt rre eaad d aan nd d
ffo ollllo ow w tth he esse e ggu uiid de elliin ne ess..
➢ ➢ T Th he e o ow wn ne err//u usse err o off tth he e ttu ub b ffiilllle err m mu usstt kke ee ep p tth hiiss iin nffo orrm maattiio on n ffo orr
ffu uttu urre e rre effe erre en ncce e..
➢ Be sure your installation conforms to federal, state, and local
codes. Anti scald protection is the responsibility of the installer
and according to applicable codes.
➢ This tub filler should be on-site prior to rough in and allows the
installer to visualize the installation and verify the center spread.
➢ Check tub deck and tub measurements to assure the spout
projects far enough into the tub.