Waterworks Easton Classic Handshower On Hook with White Porcelain Handle - Manual

3"
9"
2 1 / 4 "
Optional
Handle
EAHS13-K
4 1 / 2 " - 5"
Notes:
• 1 /
2
" female IPS inlet
• Anti scald protection is the responsibility of the
installer and according to applicable codes
• 59" hose
Easton ® Handshower on Hook
These guidelines have been prepared for the professional contractor to aid in the installation of:
EASTON
® HANDSHOWER ON HOOK
(EAHS12-K,13-K,14-K,15K)
All dimensions are based on original specifications and are subject to change and variation.
Please consult your Design Associate for current specifications.
Installation Guidelines
1
W A T E R W O R K S ®
01/04
HANDSHOWER ON HOOK
EAHS12-K (metal handle)
EAHS13-K (white porcelain handle)
EAHS14-K (black porcelain handle)
EAHS15-K (oak handle)
INSTALLATION GUIDELINES:
IMPORTANT:
➢
➢ T To o e en nssu urre e tth hiiss p prro od du ucctt iiss iin nssttaalllle ed d p prro op pe errllyy,, yyo ou u m mu usstt rre eaad d aan nd d
ffo ollllo ow w tth he esse e ggu uiid de elliin ne ess..
➢ ➢ T Th he e o ow wn ne err//u usse err o off tth hiiss p prro od du ucctt m mu usstt kke ee ep p tth hiiss iin nffo orrm maattiio on n ffo orr
ffu uttu urre e rre effe erre en ncce e..
➢ ➢ T Th he e rriisskk o off ssccaalld diin ngg e ex xiissttss u un nttiill tth he e iin nssttaalllle err h haass p prro op pe errllyy
ccaalliib brraatte ed d tth he e tte em mp pe erraattu urre e sse ettttiin ngg o on n tth he e tth he errm mo ossttaattiicc vvaallvve e
((sso olld d sse ep paarraatte ellyy))..
➢ ➢ B Be e ssu urre e yyo ou urr iin nssttaallllaattiio on n cco on nffo orrm mss tto o llo occaall cco od de ess..
➢ ➢ A A w waallll vvaallvve e ((sso olld d sse ep paarraatte ellyy)) cco on nttrro ollss o on n//o offff//vvo ollu um me e aan nd d m mu usstt
b be e iin nssttaalllle ed d ffo orr p prro op pe err o op pe erraattiio on n o off tth hiiss p prro od du ucctt..
➢ ➢ T Th hiiss p prro od du ucctt m mu usstt b be e iin nssttaalllle ed d b byy aa p prro offe essssiio on naall cco on nttrraacctto orr..
➢ ➢ R Re effe err tto o tth he e ssp pe ecciiffiiccaattiio on n aan nd d aasssse em mb bllyy d drraaw wiin nggss aattttaacch he ed d.. T Th hiiss
h haan nd d ssh ho ow we err iiss sso olld d p paarrttiiaallllyy aasssse em mb blle ed d b bu utt ssh ho ow wn n ffu ullllyy
d diissaasssse em mb blle ed d ffo orr iillllu ussttrraattiivve e aan nd d sse errvviicce e p pu urrp po osse ess o on nllyy..
➢ ➢ IInnssppeecctt tthhiiss pprro od du ucctt tto o aassssu urre e yyo ou u h haavve e aallll p paarrttss rre eq qu uiirre ed d ffo orr
p prro op pe err iin nssttaallllaattiio on n..
➢ ➢ U Usse e o on nllyy aa ssttrraap p w wrre en ncch h o orr p prro otte ecctte ed d//ssm mo oo otth h--jjaaw w w wrre en ncch h o on n
aan nyy ffiin niissh he ed d ssu urrffaacce e..
ROUGH IN:
1. Install a wall valve (sold separately) at the desired location.
Make sure the rough-in accommodates the ½" female IPS
hand shower inlet elbow.
2. Finish the rough in by installing a well supported elbow and
nipple of the proper dimensions. Note the sliding
escutcheon (19,20) has ½" of adjustment to accommodate
different nipple depths.
3. Determine the ideal location of the hook(11-18) based on
the clients preference and install blocking to properly
secure the hook.
HAND SHOWER INSTALLATION:
4. Apply pipe thread compound to the male nipple, thread on
the supply elbow (19-21) and slide the escutcheon (19, 20)
against the wall. If desired, a bead of caulk or silicone may
be applied where the escutcheon contacts the wall.
5. Turn on wall valve to flush out the hand shower supply line.
6. Thread the vacuum breaker (23) onto the supply elbow
making sure a ½" washer (22) is installed at the connection.
Over tightening may cause internal damage to the vacuum
breaker.
7. Using a 2mm hex wrench (17a), loosen the set screw (17) and
remove the mounting plate (12) from the hand shower
hook (14-18).
8. Determine the ideal location of the hook and then drill 2
holes to accommodate the mounting hardware provided.
9. Position the mounting plate (12) with the flat side facing
the wall and then secure it using the 2 anchors (11) and
screws (13) provided.
10. Position the hook against the mounting plate while making
sure the 2mm set screw is located at 6 o'clock as shown
and then tighten the set screw. The opening of the hook
MUST face to the left so the tapered end of the hose fits
properly.
11. Thread the knurled end of the hose (25) onto the vacuum
breaker then thread the conical end onto the hand shower
(1-9) making sure a ½" washer (10, 24) is included at both
connection points. Note a combination check valve with
flow restrictor are located inside the base of the hand
shower (9).
12. Turn on the wall valve and check for leaks. Rotational
adjustment of the hook can be made by removing the hook
and turning the 5mm hex bolt (14) on the back side of the
hook.
➢ If further assistance is required, please contact Product
Support at 1-800-927-2120 (8am-7pm EST).