Waterworks Astoria Thermostatic Control Valve Trim with Metal Lever Handle - Manual

Astoria Thermostatic Shower Valve & Trim
These guidelines have been prepared for the professional contractor to aid in the installation of:
ASTORIA CONCEALED THERMOSTATIC SHOWER VALVE & TRIM
(GUSV 16R + JUSV 40 AND GUSV 37R + JUSV 70)
All dimensions are based on original specifications and are subject to change and variation.
Please consult your Design Associate for current specifications.
Installation Guidelines
7/06
GUSV 16R (rough) + JUSV 40 (trim)
GUSV 37R (rough) + JUSV 70 (trim)
Includes limit stop
3 1 9 8 7 4 14 15 17 16 18
14
3
1
8 x 2
1a
1b 2
Fig. 1
15
Notes:
Rough-In depth: 2 ½” from the centerline of the
inlets to the surface of the finished wall. See
Installation Guidelines for more information.
Inlets: ¾” female NPT
Ideal operating pressure: 50-60 psi
Maximum pressure 80 psi
Minimum pressure: 25 psi
.
...
.
IMPORTANT
1. To ensure this product is installed properly, you
must read and follow these guidelines.
2. The owner/user of the valve must keep this
information for future reference.
3. This valve includes integrated service stops. Make
sure the tile guard is in place.
4. This valve features anti scald protection.The risk of
scalding exists until the installer has properly
calibrated/adjusted the temperature setting during
final trim installation.
5. Valve body rough-in depth is 2 ½" the centerline of
the inlets to the face of the finished wall.
6. Be sure your installation conforms to local codes.
7. This thermostatic valve only mixes hot and cold
water and does not have volume control or shut off
capability. A diverter or wall valves (provided sepa-
rately) control on/off/volume and must be installed
for each fitting that will have water flowing to it.
8. This product must be installed by a professional
contractor.
9. Refer to the specification and assembly drawings
attached. Valves are sold partially assembled but
shown fully disassembled for illustrative and service
purposes only.
10. If soldering any connections, remove cartridge to
prevent damage to seals and internal assembly.
11. The trim should be on-site prior to rough in and
allows the installer to visualize the installation.
12. Inspect this product to assure you have all parts
shown that are required for proper installation.
13. Check incoming water pressure; ideal operating
pressure is 50-60 psi. The minimum is 25 psi. and the
maximum is 80 psi.
GUSV16R (rough)
JUSV44 (trim)
GUSV37R (rough) + JUSV71 (trim)
3/4" Female NPT 2½" Rough-in Depth 3/4" Female NPT 2½" Rough-in Depth
(GUSV16R +JUSV44, GUSV16R + JUSV47 AND GUSV37R + JUSV71) 11.07.07
2 7
8
"
[73mm]
3 9
16
"
[90mm]
Ø2 7
16 "
[62mm]
SCALE: 3"=1'-0" TOP VIEW
FRONT VIEW SCALE: 3"=1'-0" SCALE: 3"=1'-0" SIDE VIEW
GUSV16R (rough)
JUSV47 (trim)
Astoria Thermostatic Shower Valve & Trim
These guidelines have been prepared for the professional contractor to aid in the installation of:
ASTORIA CONCEALED THERMOSTATIC SHOWER VALVE & TRIM
(GUSV 16R + JUSV 40 AND GUSV 37R + JUSV 70)
All dimensions are based on original specifications and are subject to change and variation.
Please consult your Design Associate for current specifications.
Installation Guidelines
7/06
GUSV 16R (rough) + JUSV 40 (trim)
GUSV 37R (rough) + JUSV 70 (trim)
Includes limit stop
3 1 9 8 7 4 14 15 17 16 18
14
3
1
8 x 2
1a
1b 2
Fig. 1
15
Notes:
Rough-In depth: 2 ½” from the centerline of the
inlets to the surface of the finished wall. See
Installation Guidelines for more information.
Inlets: ¾” female NPT
Ideal operating pressure: 50-60 psi
Maximum pressure 80 psi
Minimum pressure: 25 psi
.
...
.
IMPORTANT
1. To ensure this product is installed properly, you
must read and follow these guidelines.
2. The owner/user of the valve must keep this
information for future reference.
3. This valve includes integrated service stops. Make
sure the tile guard is in place.
4. This valve features anti scald protection.The risk of
scalding exists until the installer has properly
calibrated/adjusted the temperature setting during
final trim installation.
5. Valve body rough-in depth is 2 ½" the centerline of
the inlets to the face of the finished wall.
6. Be sure your installation conforms to local codes.
7. This thermostatic valve only mixes hot and cold
water and does not have volume control or shut off
capability. A diverter or wall valves (provided sepa-
rately) control on/off/volume and must be installed
for each fitting that will have water flowing to it.
8. This product must be installed by a professional
contractor.
9. Refer to the specification and assembly drawings
attached. Valves are sold partially assembled but
shown fully disassembled for illustrative and service
purposes only.
10. If soldering any connections, remove cartridge to
prevent damage to seals and internal assembly.
11. The trim should be on-site prior to rough in and
allows the installer to visualize the installation.
12. Inspect this product to assure you have all parts
shown that are required for proper installation.
13. Check incoming water pressure; ideal operating
pressure is 50-60 psi. The minimum is 25 psi. and the
maximum is 80 psi.
2 7 /
16
"
3 1 /
4
"
Astoria Thermostatic Shower Valve & Trim
These guidelines have been prepared for the professional contractor to aid in the installation of:
ASTORIA CONCEALED THERMOSTATIC SHOWER VALVE & TRIM
(GUSV 16R + JUSV 40 AND GUSV 37R + JUSV 70)
All dimensions are based on original specifications and are subject to change and variation.
Please consult your Design Associate for current specifications.
Installation Guidelines
7/06
GUSV 16R (rough) + JUSV 40 (trim)
GUSV 37R (rough) + JUSV 70 (trim)
Includes limit stop
3 1 9 8 7 4 14 15 17 16 18
14
3
1
8 x 2
1a
1b 2
Fig. 1
15
Notes:
Rough-In depth: 2 ½” from the centerline of the
inlets to the surface of the finished wall. See
Installation Guidelines for more information.
Inlets: ¾” female NPT
Ideal operating pressure: 50-60 psi
Maximum pressure 80 psi
Minimum pressure: 25 psi
.
...
.
IMPORTANT
1. To ensure this product is installed properly, you
must read and follow these guidelines.
2. The owner/user of the valve must keep this
information for future reference.
3. This valve includes integrated service stops. Make
sure the tile guard is in place.
4. This valve features anti scald protection.The risk of
scalding exists until the installer has properly
calibrated/adjusted the temperature setting during
final trim installation.
5. Valve body rough-in depth is 2 ½" the centerline of
the inlets to the face of the finished wall.
6. Be sure your installation conforms to local codes.
7. This thermostatic valve only mixes hot and cold
water and does not have volume control or shut off
capability. A diverter or wall valves (provided sepa-
rately) control on/off/volume and must be installed
for each fitting that will have water flowing to it.
8. This product must be installed by a professional
contractor.
9. Refer to the specification and assembly drawings
attached. Valves are sold partially assembled but
shown fully disassembled for illustrative and service
purposes only.
10. If soldering any connections, remove cartridge to
prevent damage to seals and internal assembly.
11. The trim should be on-site prior to rough in and
allows the installer to visualize the installation.
12. Inspect this product to assure you have all parts
shown that are required for proper installation.
13. Check incoming water pressure; ideal operating
pressure is 50-60 psi. The minimum is 25 psi. and the
maximum is 80 psi.
5 7 /
8
"
3 3 /
8
"
3 9 /
16
"
3 9 / 16 "