Dell Precision 220 - Manual (Page 74)

require serial transmission (sending one bit of data at a time over one line).
The default designations for these integrated serial ports are COM1 for serial port 1 and COM2 for serial port 2. Port designations are used in
software installation procedures to identify the port used by a device
—for example, to specify the port used by a modem when you install
communications software.
The system contains a reconfiguration feature to reassign the serial port's designation if you add an expansion card containing a serial port using
this designation.
If you set the system ’s integrated serial ports to Auto in System Setup and add an expansion card containing a serial port configured to a specific
designation, the computer automatically maps (assigns) the integrated ports to the appropriate COM setting as necessary.
Before you add a card with a serial port, check the documentation that accompanied your software to make sure that the software can be mapped
to the new COM port designation.
Parallel Port Connector
The integrated parallel port uses a 25-pin D-subminiature connector on the computer's back panel.
This I/O port sends data in parallel format (where eight data bits, or one byte, are sent simultaneously over eight separate lines in a single cable).
The parallel port is used primarily for printers.
The default designation of your computer's integrated parallel port is LPT1. Port designations are used, for example, in software installation
procedures to identify the port to which your printer is attached, thus telling your software where to send its output. (An incorrect designation
prevents the printer from printing or causes scrambled print.)
Microphone Jack
The microphone jack can be used to attach a standard personal computer microphone. Connect the audio cable from the microphone to the
microphone jack. The microphone input is a monaural source with maximum signal levels of 89 millivolts root mean squared (mVrms).
Line-Out Jack
The line-out jack can be used to attach most computer speakers. The line-out jack is amplified, so speakers with integrated amplifiers are not
required. Connect the audio cable from the speakers to this jack.
Line-In Jack
The line-in jack can be used to attach record/playback devices such as cassette players, CD players, and VCRs. Connect the line-out cable from
any of these devices to the line-in jack on the back of your computer.
Mouse Connector
Your system uses a Personal System/2 (PS/2)-compatible mouse. The mouse cable attaches to a 6-pin miniature Deutsche Industrie Norm (DIN)
connector on the back panel of your computer. Turn off the computer and any attached peripherals before connecting a mouse to the computer.
A PS/2-compatible mouse works as does an industry-standard serial mouse or bus mouse except that it has its own dedicated connector, which
frees up the serial ports and does not require an expansion card.
Mouse driver software gives the mouse priority with the microprocessor by issuing interrupt request (IRQ) 12 whenever you move the mouse. The
drivers also pass along the mouse data to the application that is in control. If you have the Microsoft
® Windows® 98 or Windows NT® 4.0
operating system, Dell already installed the necessary mouse drivers on your hard-disk drive.
Keyboard Connector
Your system uses a PS/2-style keyboard. The keyboard cable attaches to a 6-pin miniature DIN connector on the back panel of your computer.
USB Connectors
Your system contains two Universal Serial Bus (USB) connectors for attaching USB-compliant devices. USB-compliant devices are typically
peripherals such as keyboards, mice, printers, and computer speakers.
Integrated NIC Connector
Your system has an integrated 10/100-megabit-per-second (Mbps) 3Com ® Peripheral Component Interconnect (PCI) 3C920 (3C905C-TX-
compatible) Ethernet network interface controller (NIC). The NIC provides all the functions of a separate network expansion card and supports both
the 10BASE-T and 100BASE-TX Ethernet standards.
The NIC includes a Remote Wakeup feature that enables the computer to be started up by a special local area network (LAN) signal from a server
management console. Remote Wakeup provides remote computer setup, software downloading and installation, file updates, and asset tracking
after hours and on weekends when LAN traffic is typically at a minimum. Remote Wakeup can be managed through the
Dell OpenManage™ IT
Assistant .
NOTE: The integrated parallel port is automatically disabled if the system detects an installed expansion card containing a parallel port
configured to the same address as specified in
Parallel Port in System Setup .