beautypg.com

Raid controller features, Hardware requirements, Raid controller specifications – Dell PERC 4/DC User Manual

Page 48

background image

Back to Contents Page

 

RAID Controller Features

Dell™ PowerEdge™ Expandable RAID Controller 4/SC and 4/DC User's Guide

  

Hardware Requirements

  

RAID Controller Specifications

  

Configuration Features

  

Hardware Architecture Features

  

Array Performance Features

  

Fault Tolerance Features

  

Software Utilities

  

Operating System Software Drivers

  

RAID Management Utilities

 

Hardware Requirements

 

The RAID controller can be installed in a Dell™ PowerEdge™ system with a motherboard that has 5

-V or 3.3-V, 32- or 64-bit PCI slots.

 

 

RAID Controller Specifications

 

Table 2

-1

provides a summary of the specifications for the RAID controller.

 

 

Table 2-1. RAID Controller Specifications 

 

NOTE:

PERC 4/DC supports clustering, but PERC 4/SC does not.

Parameters

PERC 4/SC Specifications

PERC 4/DC Specifications

 

Card size

 

Low-profile PCI adapter card size (6.875" X 4.2")

 

Half-length PCI adapter card size (6.875" X 4.2")

 

Processor

 

Intel

®

GC80302 (Zion Lite)

 

Intel GC80303 (Zion)

 

Bus type

 

PCI 2.2

 

PCI 2.2

 

PCI bus data transfer

rate

 

Up to 532 MB/sec

 

Up to 532 MB/sec

 

Cache configuration

 

64 MB SDRAM

 

128 MB SDRAM

 

Firmware

 

Flash size is 1MB.

 

Flash size is 1MB.

 

Nonvolatile random

access memory (RAM)

 

32 KB for storing RAID configuration

 

32 KB for storing RAID configuration

 

Operating voltage and

tolerances

 

3.3V +/- 0.3V, 5V +/- 5%, +12V +/- 5%, -12V +/- 10%

 

3.3V +/- 0.3V, 5V +/- 5%, +12V +/- 5%, -12V +/- 10%

 

SCSI controller

 

One SCSI LSI53C1020 controller for Ultra320 support

 

One SCSI LSI53C1030 controller for Ultra320 support

 

SCSI data transfer rate  Up to 320 MB/sec per channel

 

Up to 320 MB/sec per channel

 

SCSI bus

 

LVD, Single-ended (SE)

 

LVD, Single-ended (SE)

 

SCSI termination

 

Active

 

Active

 

Termination disable

 

Automatic through cable and device detection

 

Automatic through cable and device detection This is automatic

capable, but jumpers by default do not allow auto termination on
PERC 4/DC.

 

Devices per SCSI

channel

 

Up to 15 Wide SCSI devices

 

Up to 15 Wide SCSI devices

 

SCSI device types

 

Synchronous or asynchronous

 

Synchronous or asynchronous

 

RAID levels supported

 

0, 1, 5, 10, 50

 

0, 1, 5, 10, 50

 

SCSI connectors

 

One 68-pin internal high-density connector for SCSI devices.

One very high density 68-pin external connector for Ultra320
and Wide SCSI.

 

Two 68-pin internal high-density connectors for SCSI devices.

Two very high density 68-pin external connectors for Ultra320
and Wide SCSI.

 

Serial port

 

3-pin RS232C-compatible connector (for manufacturing use

only)

 

3-pin RS232C-compatible connector (for manufacturing use only)

This manual is related to the following products: