SDC 800 MORTISE CYLINDER KEY SWITCH - Manual

MORTISE CYLINDER KEY SWITCH
INSTALLATION INSTRUCTIONS
SDC Key Switch Assemblies are compatible with U.S. standard, 1.125" and 1.25" mortise key cylinders and interchangeable
core cylinders (not included). Compatibility with a new or existing facility mechanical key system is maintained. Standard switch
assemblies are Single Gang box mounted. Assemblies equipped with narrow faceplates are mounted directly to the door frame.
P:\INSTALLATION INST\Exit Switches\INST-Mortise Cylinder.vsd REV D 03-13 Page 1
Switch
Mounting
Bracket
Locknut
Faceplate
Key Cylinder
SDC Part#
CYL-KD
ASSEMBLY DETAIL
TAILPIECE
Compatible with all SDC
Key Switches.
ACTUAL SIZE
Use tailpiece supplied with SDC Part# CYL-KD, or key cylinder manufacturer’s equivalent.
TAILPIECE
Compatible with all dual
switch assemblies.
Models x07 – x13
KEY SWITCH ASSEMBLY PROCEDURE
1. Check the key cylinder for the proper tailpiece (see below). For Single Switch
assemblies, use the cloverleaf type cam. For Dual Switch assemblies, a straight
cam or cloverleaf type cam may be used. If you are using an SDC supplied
cylinder, both cams will be supplied. If you are using another manufacturer’s key
cylinder, use the manufacturer’s equivalent.
2. Insert the key cylinder through the front of the faceplate. Make sure the key
cylinder is oriented correctly and the tailpiece is in the upright position.
3. While holding the key cylinder in place, slide the switch mounting bracket onto
the back of the cylinder. Align the triangular tabs on the mounting bracket with
the corresponding notches on the barrel of the key cylinder.
On the 700/700N/700T/800/800T/800AL Series, the bracket mounting holes will
align with the faceplate mounting holes.
On the 800N/800ALN Series, the mounting bracket will screw directly to the back
of the faceplate.
4. Secure the key cylinder by screwing the supplied Locknut to the back of the
cylinder. Tighten firmly. Insert key into the cylinder and verify the activation of
the switch(es) by turning the key. If necessary, adjust the switch position to
ensure that the cam makes contact with the center of the switch plunger. The
switch height should be adjusted so that the cam does not apply excessive
downward pressure to the switch.
Depth: 1.625"
(41.28mm)
All assemblies
5. Once the electrical connections are completed, mount the key switch assembly:
For the 700/800/800AL Series, attach to a single gang mortise or surface mounted box.
For the 700T/800T Series, attach to a double gang mortise or surface mounted box.
For the 700N/800N/800ALN Series, See the frame preparation illustrations on Page 2.
STANDARD FEATURES
Compatible with 1-1/8” and 1-1/4” standard and
interchangeable core mortise key cylinders (supplied by others).
Key cylinder recessed for tamper resistance. (all except 700N Series)
Tamper resistant spanner screws.
Anti-tamper plugs (800 Series)
Contact Rating: 6 amps @ 30VDC.
Wire Leads: 7", 22 gauge.
Large actuator assembly for positive & consistent circuit activation.
OPTIONAL KEY CYLINDER
CYL-KD – 1.25" Mortise Key Cylinder and (2) Keys.
Two different tailpieces included
FACEPLATE DIMENSIONS
700:
4.5"H x 2.875"W x 20 Ga.
700N: 4.5"H x 1.75"W x 20 Ga.
700T: 4.5"H x 4.5"W x 20 Ga.
800/800AL: 5"H x 3.25" W x 0.25"D
800N/800ALN: 5.5"H x 1.75" W x 0.25"D
800T: 5"H x 5" W x 0.25"D
ASSEMBLY TOOLS:
For convenience, a small spanner tool is provided with
the assembly for fastening of spanner security screws
SS-632 Standard Spanner Screw Drivers are available
Adjustable
Switch
Assembly
801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 •
www.sdcsecurity.com • E-mail: [email protected]