Prescolite MC10LED CYLINDER CORD AND CABLE MOUNT - Manual

In
s
tr
u
c
tio
n
S
h
e
e
t
Part No...........................................
With representatives offices in principal cities throughout North America.
Copyright , revision, All Rights Reserved - Printed in U.S.A.
701 Millennium Blvd • Greenville, SC 29607
w
w
w
.p
re
s
c
o
lit
e
.c
o
m
P
re
s
c
o
lit
e
T
o
ll
F
re
e
T
e
c
h
n
ic
a
l S
u
p
p
o
rt
1
.8
8
8
.P
R
S
.4
T
E
C
H
o
u
rs
: 8
a
m
-
5
p
m
E
T
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
93054545
2014 03/26/14
WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other
reproductive harm. Thoroughly wash your hands after installing, handling, cleaning, or otherwise touching this product.
NOTE: Maintain free airflow through the
fixture to avoid overheating.
CORD AND CABLE MOUNT
1. Unpack the MC10LED cylinder, the cable
mount parts bag, and the power cord from
the cylinder carton.
2. Loop the 20 foot galvanized cable around a
nearby structural member at the installation
location (Fig. 1). Assemble the crossbar and
threaded gripper as shown, using the hex
nut to lock the gripper in position. Loosen the
gripper cable lock nut and feed the cable
through the gripper as shown, and secure
the crossbar assembly to a properly installed
4" octagonal box (by others) designed to
support the weight of the fixture. NOTE: The
cable can be looped around the crossbar if
no structure is conveniently available, or if
there is no above-ceiling access (Fig. 2).
WARNING: Failure to connect the cable
end to the building structure or to a
properly installed junction box designed
to support the weight of the fixture may
allow the fixture to fall!
WARNING: Do not install cord and cable
hung fixtures in moving-air environments
such as near HVAC vents unless they are
laterally braced. Airflow may cause
continuous oscillation, which may cause
metal fatigue in the cabling system and
may cause the fixture to fall!
CEILING
Fig. 1
CABLE LOOP
AROUND
STRUCTURE
CROSSBAR
GRIPPER
HEX NUT
LOCK NUT
INSTALLATION INSTRUCTIONS
MC10LED CYLINDER
CORD AND CABLE MOUNT
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, MAKE CERTAIN THAT THE
POWER SUPPLY IS TURNED OFF BEFORE INSTALLING OR SERVICING THIS PRODUCT!
CABLE
LOOPED
AROUND
CROSSBAR
BUILDING
STRUCTURE
OCTAGONAL
BOX IN CEILING
Fig. 2
UNLOCK
PRESS
TO
RELEASE
NOTE:
HOW THE GRIPPERS
AND LOCK NUTS WORK
LOCK NUT
GRIPPER