Prescolite LB4LEDA - Manual

Instruction
Sheet
www.prescolite.com
•
Prescolite
TollFree
Technical
Support
1.888.PRS.4TEC
•
Hours:
8am
- 5pm
ET
701 Millennium Boulevard • Greenville, SC 29607
With representatives offices in principal cities throughout North America.
Copyright 2012, 5/14/12 revision, All Rights Reserved - Printed in U.S.A.
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93042403
Instruction
Sheet INSTALLATION INSTRUCTIONS
LB4LEDA SERIES
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and instructions concern-
ing Wet or Damp Locations, installation near combustible materials, insulation, building materials, and proper lamping. Do not install in areas
subject to combustible vapors or gases. Before wiring to power supply and during servicing or relamping, turn off power at fuse or circuit
breaker. All servicing or relamping must be performed by qualified service personnel. Product must be grounded to
avoid potential electric shock or other potential hazard. Product must be mounted in locations and at heights and in a
manner consistent with its intended use, and in compliance with the National Electrical Code and local codes. The use of
accessory equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block
light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
WARNING - Follow the instruction carefully to assure full compliance with local, state, and NEC requirements. If there are any questions,
contact a Qualified Electrical Contractor
WARNING - Risk of fire of electrical shock. Install this kit only in Recessed Cans matching the dimensions in Table A below.
WARNING - To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
WARNING - Risk of fire. Consult a Qualified Electrician to ensure correct branch circuit conductor.
NOTE - This product is designed to operate with most standard incandescent or low voltage electronic dimmer switches. Results may vary. For
recommended dimmers, consult product spec sheet or go to http:??www.prescolite.com or call Technical Support 1-888-PRS-4TEC
NOTE - SUITABLE FOR WET LOCATIONS IN COVERED CEILINGS
WARNING - This product contains chemicals known to the State of California to cause cancer, birth defects and/or other
reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.
NOTE - Always install within ambient temperatures specified on the product specification sheet. 5 year warranty. See www.prescolite.com
for details.
Assembly & Installation Instructions
CAUTION:
Read instructions carefully and turn electricity off at main circuit breaker panel before beginning installation.
SPEC. NO. 93041487
P8080-STR2 Series
01MAY2012
PAGE 1 OF 1
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH
THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Follow the Instruction carefully to assure full compliance with local, state, and NEC requirements. If there are any questions,
contact a Qualified Electrical Contractor.
WARNING: Risk of fire or electrical shock. Install this kit only in the Recessed Cans matching the dimensions listed below.
WARNING: To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
CAUTION: Risk of fire. Consult a Qualified Electrician to ensure correct branch circuit conductor.
NOTE: This product is designed to operate with most standard incandescent or low voltage electronic dimmer switches. Results may vary.
For recommended dimmers, consult product specification sheet for more details.
NOTE: SUITABLE FOR WET LOCATIONS IN COVERED CEILINGS
WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects and /or other reproductive harm.
Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.
NOTE: always install with ambient temperatures specified on the product specification sheet.
5 year warranty. See www.progresslighting.com for details.
Fits into Progress 4” recessed cans including: P831-AT, P832-TG, P830-TG
Fits into most competitive recessed cans with “A” and “B” dimensions above including: Capri DY1402; Commercial Electric HBR2000B (H9);
Elco EL99ICA; Halo H99ICT, H99T; Intense I4AIC; Juno IC1, TC1; Lithonia LT3, L3, L3R; Nora HSIC-401AT, NSIC-40QAT, HS-401Q,
NSR-404Q, NS-401Q.
See www.progresslighting.com for more details.
IMPORTANT!
Prior to retrofit installation, recessed can must be properly installed and flush with the ceiling. It may be necessary to detach the
socket from a mounting bracket or spring. Remove and discard bracket to allow adequate clearance.
1. Connect Trim to Power
For retrofit : Screw socket adapter (1) into socket (2) as shown. Or to hard-wire: Cut medium base screw shell socket wires near socket, discard
socket. Cut and remove screw shell adapter from trim, discard adapter. Strip wires and connect (Blk-Blk, Wht-Wht) with UL listed connectors.
For new construction with dedicated LED housing: Remove socket adapter assy (1) and discard. Connect trim connector (3) directly to mating LED
housing connector (4) as shown.
2. Insert Trim into Recessed Can
Guide socket and wiring toward the can opening . Push trim up into recessed can firmly engaging the spring clips (5) until flush with ceiling.
"A"
"B"
DIAMETER
RETROFIT
DEDICATED LED HOUSING
FOR TITLE 24
KEEP THESE INSTRUCTIONS
"A" = 4" MIN. 4 5/16" MAX.
"B" = 5" MIN.
1
2
1
4
5
5
3
Fits into Prescolite 4" recessed cans including: BX4QL-120, IBX4QL-120, RMN4QL-120
Fits into most competitive recessed cans with “A” and “B” dimensions above including: Capri DY1402; Commercial ELectric HBR2000B (H9);
Elco EL99ICA; Halo H99ICT, H99T; Intense I4AIC; Juno IC1; Lithonia LT3, L3, L3R; Nora HSIC-401AT, NSIC-40QAT, HS-401Q, NSR-404Q,
NS-401Q
See www.prescolite.com for more details.
IMPORTANT! Prior to retrofit installation, recessed can must be properly installed and flush with the ceiling. It may be necessary to detach
the socket from a mounting bracket or spring. Remove and discard bracket to allow adequate clearence.
1. Connect Trim to Power
For retrofit: Screw socket adapter (1) into socket (2) as shown. Or to hard-wire: Cut medium base screw shell socket wires near socket,
discard socket. Cut and remove screw shell adapter from trim, discard adapter. Strip wires and connect (Blk-Blk, Wht-Wht) with UL listed con-
nectors.
For new constructionwith dedicated LED Housing: Remove socket adapter assy (1) and discard. Connect trim connector (3) directly
to mating LED housing connector (4) as shown.
2. Insert Trim into Recessed Can
Guide socket and wiring toward the can opening. Push trim up into recessed can firmly engaging the spring clips (5) until flush with ceiling.
KEEP THESE INSTRUCTIONS
“A” = 4" MIN. 4 1/4"
“B”= 5"