Prescolite RLF8LED - Manual

Instruction
Sheet
www
.prescolite.com
Prescolite T
ollFree T
echnical Suppor
t
1.888.PRS.4TEC
Hours: 8am - 5pm ET
701 Millennium Blvd, Greenville, SC 29607
With representatives offices in principal cities throughout North America.
Copyright 2010, 9/23/10, All Rights Reserved - Printed in U.S.A.
Part No ....................................................... 93032580
Sheet 1 of 1
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and instructions
concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and proper lamping. Do
not install in areas subject to combustible vapors or gases. Before wiring to power supply and during servicing or relamping, turn
off power at fuse or circuit breaker. All servicing or relamping must be performed by qualified service personnel.
Product must be grounded to avoid potential electric shock or other potential hazard. Product must be
mounted in locations and at heights and in a manner consistent with its intended use, and in compliance
with the National Electrical Code and local building codes. The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from product in
whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or the like to come into
contact with the product or to block light from the product, as this may cause an unsafe condition.
WARNING - This product contains chemicals known to the State of California to cause cancer, birth defects and/or other
reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.
PREPARATION: Current reflector and lamp must be removed. Supply line must be disconnected to current socket. The
current socket can be set aside above the ceiling or removed completely. Power must be turned off and the supply line must
be brought to the opening in ceiling as shown below.
A. Connect quick connect (1) to the supply line. Remove junction box cover (3) attach supply line to junction box (4) through
one of the knock-outs provided in junction box (4). Connect connector (1) to connector (2). Put all wires inside of junction
box (4) and install junction box cover (3). (SEE FIG. 1)
WARNING: DO NOT pinch wires between J-Box/ballast cover and J-Box. Consult a qualified electrician for all other
options that require other wiring configurations. Make sure all connections are tight and secure.
B. Push junction box Assembly and flange ring (5) through hole in ceiling. (SEE FIG. 2)
C. With housing (5) in ceiling, the housing (5) can be rotated as needed to clear existing fixture obstacles and/or to be
positioned best for the flexible conduit, etc. If additional adjustment is needed, screw (6) and/or screw (7) can be
loosened and junction box (2) can be further moved. Ensure that screw (6) and (7) are retightened after this step. (SEE
FIG. 3)
D. While pressing the bottom flange (8) tight against the bottom of the ceiling insert one support (9) into slot as shown. Press
support (9) down against the top of the ceiling and tighten screw (10). Repeat this step for other support (9) on opposite
side. (SEE FIG.4)
E. Install bracket (11) into slot on housing. Hold bracket (11) down firmly against top of housing ring (8) and tighten screw
(12) to secure bracket (11). Repeat this step for other bracket (11). (SEE FIG 4)
F. Pull connector (13) and electrical cover (14) below ceiling and plug connector (13) into module (15). Snap electrical
cover (14) onto module (15) ensuring that both clips (16) engage electrical cover (14). Insert two torsion springs (17) into
two brackets (11) and push trim assembly (18) towards ceiling until springs pull trim assembly firmly against ceiling. (SEE
FIG. 5 and 6)
INSTALLATION INSTRUCTIONS
RLF6LED/RLF8LED
2
3
1
4
5
11
17
14
13
15
16
18
6
7
9
10
11
12
8
FIG. 4
FIG. 3
FIG. 6
FIG. 1
FIG. 2
FIG. 5