beautypg.com

Prescolite LD6_P User Manual

Ins tru ctio n s he et, Installation instructions ld6_p series, W.p re sc olit e.c om

background image

Cam Action

Retention

Mounting plate with keyhole

slots (screws do not have to be

removed from Outlet Box)

3/4” or 4” Outlet Box

Ins

tru

ctio

nS

he

et

w

w

w

.p

re

sc

olit

e.c

om

• P

res

co

lite

To

llF

ree

Te

ch

nic

al S

up

po

rt

1.8

88

.P

RS

.4T

EC

H

ou

rs:

8a

m

- 5

pm

E

T

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93011924

Ins

tru

ctio

nS

he

et

INSTALLATION INSTRUCTIONS

LD6_P SERIES

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information

and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,

and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and

during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by

qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.

Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in

compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by

the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from

product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or

the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.

WARNING - This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other

reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.

701 Millennium Boulevard • Greenville, SC 29607

With representatives offices in principal cities throughout North America.

Copyright 2009, 10/30/09 revision, All Rights Reserved - Printed in U.S.A.

FIG. 1

FIG. 2

PENDANT MOUNT

1. Make electrical connections. Connect ground wires to green ground

leads. Connect white (common) to white leads. Connect power supply

(line) to black leads. (see wiring diagram).
WARNING: DO NOT pinch wires. Consult a Qualified Electrician for

all other options that require other wiring configurations.

2. Fasten mounting plate to outlet box.
3. Twist canopy cover in place. (Fig. 1)

INSTALLATION

1. Insert supplied #8-32 x 1/2” screws into supplied S-4 strap through

tapped holes located 2-3/4” apart in orienation shown in Fig 1. (Holes in

fixture canopy must line up with these screws.)

2. Mount strap to outlet box with screws (by others) with screw stems fac-

ing outward. Rotate strap to adjust fixture to correct position.

3. Connect supply wires: Black to Line, White to Common, Green to

Ground. (DM only: Connect Gray (+) and Violet (-) to appropriate 0-10V

dimming control per National Electrical Code and local codes.

4. Secure fixture canopy with two mounting nuts supplied.

5. Fixtures used in wet locations, place the two supplied o-rings under the

heads of the mounting screws and secure mounting nuts. Area around

fixture canopy and mounting surface must be sealed.

LIGHT ENGINE REPLACEMENT

1. Remove lensed reflector assembly by pulling from the edges. Reflector

assembly is held by a safety cable.

2. Loosen captive screw holding the light engine. Carefully lower and dis-

connect light engine connector from driver connector. See Fig. 2.

3. Connect replacement light engine connector to driver connector and

line up light engine heat sink fins with mounting bracket until seated

into place and tighten captive screw.

4. Reinstall reflector assembly.

LED DRIVER REPLACEMENT

1. Remove lensed reflector assembly by pulling from the edges. Reflector

assembly is held by a safety cable.

2. Loosen captive screw holding the light engine. Carefully lower and dis-

connect light engine connector from driver connector. See Fig. 2. Set

aside.

3. Remove driver bracket mounting screw attaching safety cable and

remove reflector assembly. Set aside.

4. Remove remaining driver bracket mounting screws and lower driver

bracket. Disconnect all driver wiring and replace driver by removing

driver mounting screws. See Fig 2.

5. Mount replacement driver and reconnect wiring according to installation

step 3.

6. Reinstall driver bracket and safety cable holding reflector assembly

using mounting screws. Reconnect light engine connector to driver con-

nector and line up light engine heat sink fins with mounting bracket until

seated into place and install with captive screw.

7. Reinstall reflector assembly.

NOTE: Do not pinch LED wires between the sliding parts.
KEEP THESE INSTRUCTIONS

Canopy

Outlet Box
Mounting Screws

Screws #8-32

(2)

Strap

Light Engine
Mounting Screw

Trim

Driver
Mounting Screws

Driver Bracket

Driver Bracket
Mounting Screws

Light Engine

Connector

Driver
Mounting Screws

Connector

Driver Bracket
Mounting Screws

Driver Bracket

Light Engine
Mounting Screw

Light Engine

Trim

Driver
Mounting Screws

Connector

Driver Bracket
Mounting Screws

Driver Bracket

Light Engine
Mounting Screw

Light Engine

Safety Cable

Trim

Safety Cable