Prescolite SLOPED CEILING ADAPTORS - Manual

www.prescolite.com
• Prescolite
TollFree
Technical
Support
1.888.PRS.4TEC
•
Hours:
8am
- 5pm
ET
701 Millennium Boulevard • Greenville, SC 29607
With representatives offices in principal cities throughout North America.
Copyright 2010, 02/10 revision, All Rights Reserved - Printed in U.S.A.
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01863200
Instruction
Sheet
INSTALLATION INSTRUCTIONS
SLOPED CEILING ADAPTORS
NOTE: BEFORE INSTALLING THE RECESSED HOUSING IN CEILING, FOLLOW THE
INSTRUCTIONS FOR FIGURE 1, 2, 3, AND 4 TO ATTACH THE CEILING ADAPTOR TO
THE HOUSING . THEN FOLLOW THE INSTRUCTIONS FOR FIGURE 5 TO INSTALL THE
HOUSING/ ADAPTOR ASSEMBLY INTO THE CEILING.
TOOLS REQUIRED:
FOR FIGURE 1 SCALE; DRILL; #29 (.136) DIA DRILL; 8-32 UNC-28 TAP;
5
/
64
” HEX KEY
FOR FIGURE 2&3: DRILL;
1
/
2
” DIA. DRILL;
3
/
16
” DIA DRILL;
5
/
16
” STRAIGHT SCREWDRIVER
FOR FIGURE 4: DRILL;
3
/
16
” DIA DRILL;
5
/
16
” STRAIGHT SCREWDRIVER
DRILL & TAP FOR 8-32 SCREW
(2) AT 180° OR (3) AT 120°
MINOR AXIS OF HOUSING
HOUSING PLASTER FLANGE
WET CEILING ADAPTOR
(FLANGELESS)
MAGOR AXIS OF ADAPTOR
SLOPE OF CEILING
8-32 SET SCREWS
DRY CEILING ADAPTOR
(FLANGE)
FIGURE 1
FIGURE 1. (NEW METHOD) ATTACHMENT OF SCA3/5/6/8/10/12/13 CEILING ADAPTORS TO DIECAST
ALUMINUM PLASTER FLANGE HOUSINGS.
1. Locate up
1
/
4
” from bottom of housing plaster flange. Drill #29 (.136) dia. hole and tap #8-32 UNC-2B.
NOTE: For SCA3/5/6/8 adaptors - drill and tap (2) holes 180° apart or (3) holes 120° apart.
For SCA10/12/13 adaptors - drill and tap (3) holes 120° apart.
2. Install 8-32 x
1
/
4
” set screws (included in packet) in tapped holes.
3. Place ceiling adaptor on housing plaster flange.
4. Align MAJOR AXIS of ceiling adaptor with MINOR AXIS of fixture housing.
5. Tighten set screws to secure ceiling adaptor to housing plaster flange.
6. Turn to page 4 and follow FIGURE 5 instructions.
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
WARNING - This product contains chemicals known to the State of California to cause cancer, birth defects and/or other
reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.