Prescolite MC10LED CYLINDER SURFACE/CEILING MOUNT - Manual

In
s
tr
u
c
tio
n
S
h
e
e
t
Part No...........................................
With representatives offices in principal cities throughout North America.
Copyright , revision, All Rights Reserved - Printed in U.S.A.
701 Millennium Blvd • Greenville, SC 29607
w
w
w
.p
re
s
c
o
lit
e
.c
o
m
P
re
s
c
o
lit
e
T
o
ll
F
re
e
T
e
c
h
n
ic
a
l S
u
p
p
o
rt
1
.8
8
8
.P
R
S
.4
T
E
C
H
o
u
rs
: 8
a
m
-
5
p
m
E
T
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
93052567
2014 02/24/14
WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other
reproductive harm. Thoroughly wash your hands after installing, handling, cleaning, or otherwise touching this product.
INSTALLATION INSTRUCTIONS
MC10LED CYLINDER
SURFACE/CEILING MOUNT
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, MAKE CERTAIN THAT THE
POWER SUPPLY IS TURNED OFF BEFORE INSTALLING OR SERVICING THIS PRODUCT!
NOTE: Maintain free airflow through the fixture to
avoid overheating.
SURFACE MOUNT
1. Unthread the mounting channel from the top of the
fixture (in the canopy, as shipped). Insert the supplied
power wiring (and control wiring, if needed) through the
opening in the mounting channel. Make the ground
connection to the ground screw on the mounting
channel and secure the mounting channel assembly to
a properly installed 3-1/2"or 4" octagonal box (by
others) designed to support the weight of the fixture
(Fig. 1). NOTE: The end slots in the mounting channel
are provided for additional structural mounting security.
Additional bolts attached to the building structure
through these slots are recommended for applications
where vibration may be encountered.
2. Make the electrical connections in the outlet box.
Connect the supply lead wires to the fixture lead wires
in the mounting channel using properly sized UL listed
wire connectors. Connect the line voltage to the black
wire, the neutral to the white wire, and make any control
connections to the proper control wires. Place the wiring
and connections in the junction box.
3. Carefully stand the cylinder on its top canopy (the
finned, cast end). Loosen (do not remove) the two
Phillips screws on opposite sides of the cylinder (near
the vent slots) until the screws disengage from the
internal locking slots and the cylinder housing is free to
slide. Slide the outer cylinder housing open towards the
reflector (it should move about 7 inches from the top
finned casting) and tighten the two Phillips screws until
the cylinder housing maintains its open position (Fig. 2).
4. Loosen the two thumbscrews holding the wiring
compartment cover closed, rotate and lift the cover free,
and carefully slide it out of the way (there is a safety
cable to hold it while the wiring is being completed).
Fig. 1
OUTLET BOX
OPENING
MOUNTING
CHANNEL
SUPPLIED
WIRING
Fig. 2
PHILLIPS
SCREW
(1 OF 2)
CANOPY
THUMBSCREW
(1 OF 2)
WIRING
COMPARTMENT
COVER
SLIDE
HOUSING
OPEN