Prescolite 6LCLEDEM - Manual

Instruction
Sheet
www.prescolite.com
• Prescolite TollFree Technical Support
1.888.PRS.4TEC
• Hours: 8am - 5pm ET
701 Millennium Boulevard • Greenville, SC 29607
With representatives offices in principal cities throughout North America.
Copyright 2014, 6/23/14 revision, All Rights Reserved - Printed in U.S.A.
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93050908
Instruction
Sheet
INSTALLATION INSTRUCTIONS
LITEFRAME
®
LC6LEDEM & 6LCLEDEM
1. Install the fixture in the ceiling using the hanger bars (supplied), or mounting channel or bars (by others) placed in the adjustable mounting brackets. Mount
the fixture in the ceiling so that the weight of the fixture is supported by the hanger bars, mounting channel, bar, and/or hanger wires secured to the building
structure.
2. Adjust the fixture so the bottom of the plaster flange opening is flush with the finished ceiling line and in alignment with adjacent fixtures. Secure mounting
brackets by tightening wing nuts on either side of the fixture.
3. Determine where the supply wiring conduit will enter the J-Box and attach it in conformance with the National Electric Code.
4. Remove J-Box cover plate. Remove appropriate knockout and assemble appropriate connector for the supply wire used. Connect ground wires to green ground
leads. Connect white (common) to white (leads). Connect power supply (line) to black lead(s). Reinstall J-Box cover.
WARNING: DO NOT pinch wires between J-Box/ballast cover and J-Box. Consult a qualified electrician for all other options that
require other wiring configurations.
5. Pull electrical cover (1) and EM Test Switch (2) down through opening in fixture.
6. Remove nut (3) from Test Switch. Insert Test Switch into Bracket (4) and install and tighten nut. Position Test Switch as shown below with conduit facing upward.
7. Insert connector (5) into connector (6) and snap firmly together.
8. Carefully put wires and connectors (5) & (6) into cover (1). Place tab (7) into slot of reflector (8) and screw (9) into hole in reflector (8). Make sure there are not
any wires pinched between item (1) and item (8). Tighten screw (9).
9. Squeeze two torsion springs (10) together and insert ends into two brackets (11).
10. Push trim assembly up towards ceiling until springs draw trim firmly against the ceiling.
11. Care must be taken to insure that the yellow/red wires are appropriately connected/not connected per table 1 on the Bodine BSL310C instruction sheet
(included). The 6LCLED5/6LCLED6 light engines are between 10V and 29V and the 6LCLED7 light engine is between 30V and 50V.
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and
instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and
proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and during
servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other poten-
tial hazard. Product must be mounted in locations and at heights and in a manner consistent with its
intended use, and in compliance with the National Electrical Code and local codes. The use of accessory
equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe condition. Do
not block light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such
as drapes, curtains, screens or the like to come into contact with the product or to block light from the product, as this may
cause an unsafe condition.
WARNING - This product contains chemicals known to the State of California to cause cancer, birth defects and/or other
reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.
CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND
PROPER OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.
*See important wiring note 11.