Prescolite 4LFLEDWW User Manual

Instruction sheet, Installation instructions liteframe, Lf4led, 4lfled, and 4lfledww

Instruction

Sheet

www.prescolite.com

•

Prescolite

TollFree

Technical

Support

1.888.PRS.4TEC

•

Hours:

8am

- 5pm

701 Millennium Boulevard • Greenville, SC 29607

With representatives offices in principal cities throughout North America.

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93036004

Instruction

Sheet

INSTALLATION INSTRUCTIONS

LITEFRAME

LF4LED, 4LFLED, and 4LFLEDWW

1. Install the fixture in the ceiling using the

hanger bars (supplied), or mounting

channel or bars (by others) placed in the

adjustable mounting brackets. Mount the

fixture in the ceiling so that the weight of

the fixture is supported by the hanger bars,

mounting channel, bar, and/or hanger

wires secured to the building structure.

2. Adjust the fixture so the bottom of the

plaster flange opening is flush with the

finished ceiling line and in alignment with

adjacent fixtures. Secure mounting brackets

by tightening wing nuts on either side of

the fixture.

3. Determine where the supply wiring

conduit will enter the J-Box and attach it

in conformance with the National Electric

Code.

4. Remove J-Box cover plate. Remove

appropriate knockout and assemble

appropriate connector for the supply wire

used. Connect ground wires to green

ground leads. Connect white (common) to

white (leads). Connect power supply (line)

to black lead(s). Reinstall J-Box cover.

WARNING: DO NOT pinch wires

between J-Box/ballast cover

and J-Box. Consult a qualified

electrician for all other options

that require other wiring

configurations.

5. Pull electrical cover (1) down through

opening in fixture. (SEE FIG 1)

6. Squeeze two torsion springs (2) together

and insert ends into two brackets (3). (SEE

FIG 1)

7. Insert connector (4) into module (5)
8. Insert tab (6) into bracket. Align screw (7)

with hole and tighten. (SEE FIG. 1)

9. Push trim assembly up towards ceiling until

springs draw trim firmly against ceiling.

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and

instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and

proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and during

servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by

qualified service personnel. Product must be grounded to avoid potential electric shock or other poten-

tial hazard. Product must be mounted in locations and at heights and in a manner consistent with its

intended use, and in compliance with the National Electrical Code and local codes. The use of accessory

equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe condition. Do

not block light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such

as drapes, curtains, screens or the like to come into contact with the product or to block light from the product, as this may

cause an unsafe condition.

WARNING - This product contains chemicals known to the State of California to cause cancer, birth defects and/or other

reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.

CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND

PROPER OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.

FIG 1

4LFLED WW

FIG. 4

FIG. 1

FIG. 2

FIG. 6

FIG. 7

RING A

FIG. 3

RING B

FIG. 5

RLC6LEDSD  93046994

FIG. 3

FIG. 1

FIG. 2

FIG. 4

FIG. 5

FIG. 6

RLC6LED  93046993

FIG. A

FIG. B

IFNEEDED REMOVE SCREW
AND BRACKET. REINSTALL
AFTER RING IS MOUNTED
IN CEILING.

replace line art on
93036004 with this

Item 3 can be put

in other locations to

change orientation of

wall wash.

Note: Heatsink

can not go

towards J-Box on

WW version

This manual is related to the following products:

4LFLED LF4LED