Prescolite D2FRM User Manual

Sh ee t, Instruction sheet, Inst ruction

Instruction

Sheet

www.prescolite.com

•

Prescolite

TollFree

Technical

Support

1.888.PRS.4TEC

•

Hours:

8am

- 5pm

701 Millennium Boulevard • Greenville, SC 29607

With representatives offices in principal cities throughout North America.

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93040525

Instruction

Sheet

INSTALLATION INSTRUCTIONS

MODEL D2FRM

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and

instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and

proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and during

servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by

qualified service personnel. Product must be grounded to avoid potential electric shock or other poten-

tial hazard. Product must be mounted in locations and at heights and in a manner consistent with its

intended use, and in compliance with the National Electrical Code and local codes. The use of accessory

equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe condition. Do

not block light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such

as drapes, curtains, screens or the like to come into contact with the product or to block light from the product, as this may

cause an unsafe condition.

WARNING - This product contains chemicals known to the State of California to cause cancer, birth defects and/or other

reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.

CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND

PROPER OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.

KEEP THESE INSTALLATION INSTRUCTIONS

Inst
ruction

Part No...........................................

With representatives offices in principal cities throughout North America.

701 Millennium Blvd., Greenville, SC 29607

www.pr

lite

.co

Prescoli

oll

Fre
e T

hni

l S

upp

ort

1.88

8.P

S.4

rs:

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information

and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,

and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and

during servicing or relamping, turn off power at fuse or circuit breaker.

All servicing or relamping must be performed by

qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.

Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in

compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by

the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from

product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or

the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.

93040525

2012 01/17/12

WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other

reproductive harm. Thoroughly wash your hands after installing, handling, cleaning, or otherwise touching this product.

CENTER

LINE

LIN

D2FRM TOP VIEW

Bend

Tabs

8" x 8"

Polycarbonate

Panel

Cut-Through

Area

Flexible Conduit

Holding Clips

Seismic

Tether

D2FRM WITH D2LED INSTALLED

DETAIL A

Seismic

Tether

D2LED

Fixture Screw

1. The bar hanger brackets are shipped flat. Bend the tabs

on the brackets as shown to allow the use of accessory
mounting channels or bar hangers (Prescolite B6, B24,

or by others). Mount the frame in the ceiling so that the

weight of the assembly is safely supported by the
mounting channel or bar and/or hanger wires secured
to the building structure.

2. Adjust the frame so the bottom surface is flush with the

ceiling material mounting surface (backside of the
ceiling material) and in alignment with adjacent fixtures.
The rivets for the 8” x 8” polycarbonate cut-through

panel may be used as centerlines (as shown) for
aligning the frame. (Note the brackets may be flipped
over if needed for additional vertical adjustment.)
Secure the mounting brackets by tightening wing nuts

on either side of the frame.

3. Important! When the ceiling material is added

(covering the D2FRM) make sure the D2FRM is
flush with the back side of the ceiling material

and solidly mounted. Mark the fixture
installation location accurately so the hole cut-
through location will be accurate!

4. There are two spring clips located on the topside of the

D2FRM to allow the UNENERGIZED line voltage and
control (0-10V dimming) flexible conduit to be

temporarily held until they are used when the D2LED

fixture is wired and installed. There is also a tether
cable mounted to the D2FRM to be attached to the
D2LED fixture in the case of seismic conditions at the
install location. This tether, if needed, should be

attached to the screw on the light engine (see Detail A)
after the wiring is complete and the J-tube is inserted in
the ceiling, but before fixture is installed.

5. Install the D2LED fixture per the instruction sheet

provided with the fixture. When the hole is cut in the
ceiling with the 2-7/8” hole saw (by others), it will cut
through the ceiling material and the D2FRM
polycarbonate cut-through panel at the same time

providing accurate alignment in both the ceiling
material and the D2FRM.

6. WARNING: DO NOT pinch wires between J-

tube cover and J-tube endplates. Consult a
Qualified Electrician for all other options that
require other wiring configurations.

CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND

PROPER OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.

KEEP THESE INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

MODEL D2FRM