J11 guard – MTS Criterion 40 - Manual User Manual
Page 75
Installing Cables
MTS Criterion
®
Series 40 Product Manual
Installation
75
J11 Guard
The connector should be connected to the safety system (Enclosure switch) or
jumpered for crosshead motion.
The enclosure switch has two NC contacts. One must be connected between Pin
1 and Pin 6. The other must be connected between Pin 2 and Pin 7.
GUARD_CONFIG1/2-jumpers determine if crosshead motion slows to 540 mm/
min or comes to a complete stop when the enclosure door opens. That is to say,
No Jumpers = complete stop with door open.
Jumpers from Pin3-Pin8 and Pin5-Pin9 = crosshead slows to 540 mm/min with
the enclosure door open.
Pin assignments are as follows:
P
IN
S
IGNAL
1
GUARD1A+
2
GUARD2A+
3
GUARD_CONFIG1+
4
No Contact
5
GUARD_CONFIG2-
6
GUARD1A -
7
GUARD2A-
8
GUARD_CONFIG1-
9
GUARD_CONFIG2+
Criterion_product manual.book Page 75 Monday, July 28, 2014 3:52 PM
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)