Load cell mounting, Load cell mounting 109 – MTS Criterion 40 - Manual User Manual
Page 109
Load Cell Mounting
MTS Criterion
®
Series 40 Product Manual
Operation
109
Load Cell Mounting
Mounting load cells typically involves securing the load cell to the frame via a
threaded bolt along with associated hardware (in most cases a flat washer,
adapter sleeve, and plate assembly). The following figures show the standard
mounting configurations. Load cell mounting/adapter bolts should be lubricated
with light oil or grease before being assembled and torqued to specifications. See
“Load Cell Bolt Torque Specifications”
on page 112.
When installing a mounting bolt or an adapter bolt into load cell, check the length
of bolt to avoid “bottoming” the bolt in the load cell hole. Doing so will
permanently damage the load cell.
On C41 and C42 S-beam style cells, support the grip adapter while torquing the
adapter bolt to prevent damaging the load cell from torque twist.
Model C41 1 N-1 kN
Load Cell
Plate Assembly
Sleeve
Washer
Cap Screw
Load Cell
Plate Assembly
Sleeve
Washer
Cap Screw
Model C42 1 N-5 kN
Criterion_product manual.book Page 109 Monday, July 28, 2014 3:52 PM
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)