INFICON HLD6000 Refrigerant Leak Detector - Manual (Page 4)

4
Table of Contents
Tr
an
sl
ation
o
f the
o
rig
in
al
operatin
g
in
str
u
ct
io
ns
HLD
6000
, k
ina4
3
e1-
a
, 140
8
6.3.6 Set time interval for calibration request ............................................................................................................. 36
6.3.7 Switching the request for replacing filters on or off ...................................................................................... 36
6.3.8 I/O module .................................................................................................................................................................... 36
6.3.8.1 Create a connection between the device and the I/O module ................................................................. 36
6.3.8.2 Configuring analog outputs ................................................................................................................................... 37
6.3.8.3 Setting the upper scale value for 10 V of the analog output ...................................................................... 37
6.3.8.4 Setting up the I/O module protocol .................................................................................................................... 37
6.3.8.5 Configuring PLC outputs ......................................................................................................................................... 37
6.3.8.6 Configuring PLC inputs ............................................................................................................................................ 38
6.3.8.7 Setting the interface unit ......................................................................................................................................... 38
6.3.9 Set up scope of error messages ............................................................................................................................ 38
6.3.10 Access to the settings ............................................................................................................................................... 39
6.3.10.1 Protecting settings via PIN assign ........................................................................................................................ 39
6.3.10.2 Switching between "supervisor" and "operator" modes ............................................................................. 39
6.3.10.3 Changing parameter access levels ....................................................................................................................... 40
6.3.11 Save parameters ......................................................................................................................................................... 40
6.3.12 Load parameters ......................................................................................................................................................... 40
6.4 Settings for the measurements ............................................................................................................................ 41
6.4.1 Setting setpoints ......................................................................................................................................................... 41
6.4.2 Setting up the sniffer probe ................................................................................................................................... 41
6.4.3 Setting up an alarm profile for setpoints ........................................................................................................... 41
6.4.4 Setting up the gas for the SMART sniffer line ................................................................................................... 42
6.4.5 Verifying R290 with the sniffer line for R600a/R290 ....................................................................................... 43
6.4.6 Calibration ..................................................................................................................................................................... 43
6.4.6.1 Time and type of calibration .................................................................................................................................. 43
6.4.6.2 Calibration with an internal COOL-Check .......................................................................................................... 44
6.4.6.3 Calibration with an external calibration leak ................................................................................................... 45
6.4.6.4 Checking the calibration with an internal COOL-Check ............................................................................... 45
6.4.7 Measuring .................................................................................................................................................................... 46
6.4.8 Measured data ............................................................................................................................................................. 47
6.4.8.1 Recording measured data ....................................................................................................................................... 47
6.4.8.2 Evaluating measured data ....................................................................................................................................... 48
6.4.8.3 Transferring measured data from the internal memory to a USB stick ................................................... 48
6.4.8.4 Deleting measured data .......................................................................................................................................... 49
6.5 Standby ......................................................................................................................................................................... 49
6.6 Diagnosis ...................................................................................................................................................................... 49
6.7 Calling up information about the device .......................................................................................................... 49
6.7.1 Parameter list ............................................................................................................................................................... 50
6.8 Updating the software .............................................................................................................................................. 51
6.8.1 Updating the software of the basic unit ............................................................................................................ 52
6.8.2 Updating the software of the operating unit ................................................................................................... 52
6.8.3 Updating the software of the sniffer line ........................................................................................................... 53
6.8.4 Updating the software of the I/O module ......................................................................................................... 53
6.9 Switching off the device .......................................................................................................................................... 53
7 Warning and error messages ................................................................................................................................. 55
8 Maintenance ................................................................................................................................................................ 61
8.1 Basic unit ........................................................................................................................................................................ 61
8.1.1 Replacing the filter plates ........................................................................................................................................ 61