Maintenance – ERICO LENTON Mid-Range Bar Threader User Manual
Page 22
www.erico.com
22
First step is to remove the pin located on the chip drawer.
Machine chips are caught in the screened drawer above the
oil reservoir. The drawer should be emptied as required during
the machining run and at the end of the day.
Maintenance
At the end of each day 15 minutes should be put aside to
drain the oil and clean out the oil reservoir.
The oil is drained by loosening and removing the drain plug
at the side of the oil reservoir. An oil pan and crescent wrench
is provided to accomplish this.
Let the oil sit in the oil pan overnight to allow the fine chips
to settle to the bottom. Next morning slowly pour the oil
back into the bar threader and clean out the oil pan.
2
1
3
See also other documents in the category ERICO Accessories for electrical:
- 6Z34VF14 Rod Hanging Basket Tray Clip (1 page)
- 766PM Far Side Box Support (1 page)
- 766PMD Far Side Box Support (1 page)
- CADDY MPVTI Low Voltage Mounting Clip (2 pages)
- H-Series CADDY PYRAMID Support System (3 pages)
- CADDY PYRAMID RL, PIPE RETAINERS (2 pages)
- CADDY PYRAMID Rooftop Equipment Support (4 pages)
- CADDY PYRAMID Single Post Support (1 page)
- CADDY PYRAMID TF Series, Fixed Height Tool-Free Supports (2 pages)
- CADDY ROD LOCK Anchor Screw (2 pages)
- CADDY ROD LOCK Beam Clamp (2 pages)
- CADDY ROD LOCK Channel Nut (2 pages)
- CADDY ROD LOCK L-Bracket (2 pages)
- CADDY ROD LOCK Strut (2 pages)
- CADDY SPEED LINK Riveted Accessories (4 pages)
- CADDY SPEED LINK SLK-Keyless Locking Device and Bulk Cable (2 pages)
- CADDY SPEED LINK SLK-Keyless Locking Devices (2 pages)
- CADDY SPEED LINK-Accessory Cables (1 page)
- CADDY SPEED LINK-SLK Cable End Accessories (4 pages)
- TSGB Series Screw Gun Bracket (2 pages)
- GLIDER Electrical Box Attachment (2 pages)
- H Series-Electrical Box Bracket (2 pages)
- ROD LOCK Plywood Pre-set Anchor (2 pages)
- ROD LOCK Strut End Bracket (2 pages)
- ROD LOCK Strut (2 pages)
- CADDY ROD LOCK Strut Nut (2 pages)
- CER4 Cable from Stud (2 pages)
- High Performance CADDY CAT HP J-Hook Assemblies (6 pages)
- KBT Wire Basket Tray Clip (1 page)
- MPCB1220 (2 pages)
- SBC Series, Beam Clamp, 3/8" and M10 (1 page)
- TSR200 Telescoping Strut Replacement Bracket (2 pages)
- TSRBS1625 Telescoping Box (3 pages)
- Universal Pedestal Clamp (2 pages)
- Branch Line Restraint Device (2 pages)
- Branch Line Restraint Strucural Attachment Fitting for Steel 12 gauge (2 pages)
- Branch Line Restraint, Structural Attachment Fitting for Concrete or Wood (2 pages)
- Branch Line Restraint, Structural Attachment Fitting with 3/8"-16 male thread" (2 pages)
- 510 CADDY EZ RISER (2 pages)
- 429 CADDY MACROFIX PLUS NI (1 page)
- Seismic Hanger Clamps (3 pages)
- CADDY PYRAMID Equipment Supports (3 pages)
- CADDY ROD LOCK Bottom-Mount Duct Bracket (2 pages)
- Bottom-Mount Duct Bracket, Narrow (2 pages)
- Top-Mount Duct Bracket (2 pages)