ERICO 429 CADDY MACROFIX PLUS NI User Manual
ERICO Accessories for electrical
Installation:
- Insert pipe
- Close pipe clamp by pressing
the clamp part upward
- Let screw head lock
in the tabs
- Use a screwdriver to
tighten the two screws
- Tighten pipe clamp
until tabs are parallel
UL listed for use with CPVC pipe as a
hanger and surge restraint
4.52 Nm
40 inch-lbs
Bottom Beam Installation
Finish:
Electro-galvanized Zinc
=Not UL Listed
*
*
Top Beam Installation
!
=FM Approved
!
!
!
!
!
!
!
!
!
!
*
*
**
*
To comply with UL203 Listing in the top beam installation the hex
nut of the pipe hanger must be inserted onto a threaded rod and
rest directly on the structural member.
®
®
CPVC Non-Insulated Pipe Clamp
3/8
Threaded Rod
Part Number
M10
Threaded Rod
Part Number
M12
Threaded Rod
Part Number
Nominal
Pipe Size
Inches
Outside Dia.
Of Pipe
(Inches) / mm
4290050EG
595052
1/2
(0.84) / 21.3
4290075EG
595053
3/4
(1.05) / 26.7
4290100EG
595054
1
(1.32) / 33.4
4290125EG
595056
1-1/4
(1.67) / 42.2
4290150EG
595057
1-1/2
(1.90) / 48.3
4290200EG
595059
2
(2.37) / 60.3
4290250EG
595061
596060
2-1/2
(2.87) / 73
4290300EG
595062
596062
3
(3.50) / 88.9
4290350EG
3-1/2
(4.00) / 101.6
4290400EG
595063
596063
4
(4.50) / 114.3
4290500EG
595066
5
(5.56) / 141.3
INSTRUCTION SHEET
All rights reserved. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
TECHNICAL SUPPORT:
www.erico.com
CFS397_H
INSTRUCTION SHEET
NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.
The customer is responsible for:
a. Conformance to all governing codes.
b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer.
c. Using appropriate industry standard hardware as noted above.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed.
Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
1 OF 1
© 2009, 2010, 2011 ERICO International Corporation
WARNING:
ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at
1.
www.erico.com and from your ERICO customer service representative.
ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
2.
All instructions must be completely followed to ensure proper and safe installation and performance.
3.
Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property
4.
damage, serious bodily injury and death.
Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.
5.
All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any
6.
other purpose.
®
FM is a registered certification mark of FM Approvals LLC, LTD
UL is a registered trademark of Underwriters Laboratories, Inc.