Sioux Chief 523-3MS Series Overhead Bracketing System User Manual
Overhead bracketing system

OVERHEAD BRACKETING SYSTEM
523-3MS SERIES
SPECIFICATION
Sioux Chief 523-3MS series Heavy Duty PowerBar Mini Strut shall be used
where necessary for hanging pipes overhead from " threaded rod. Bracket
shall be corrosion resistant. System shall include adjustable channel clamps
with elastomer inserts for fastening any pipe, tube, cable, etc. up to 2" maximum
diameter. Bracket shall be used with Sioux Chief Touchdown Clamps or Sioux Chief
Touchdown II Clamps. System shall be approved for use with insulated or non-
insulated copper tube, CPVC tube, PEX/PB tube, steel pipe, CSST lines, plastic or
steel conduit and low voltage DataCom cable. System shall be UV resistant.
INSTALLATION
Once adjustable clamps are installed in bracket channel, install onto " all-
thread rod and suspend bracket, using approved " hex nuts and washers. When
specified, use hardware above and below bracket channel. Move adjustable clamps
to desired location within bracket channel. Place conduit between clamp posts
and engage clamp bridge. Ratchet bridge of channel clamp down over both posts
evenly. Install optional Sioux Chief Touchdown II adjustable clamp to secure large
diameter pipe or tube up to 2" diameter. Approved galvanized two-hole pipe strap
fastened directly to bracket is acceptable. Optional SaddleUp™ clamp from Sioux
Chief with stainless steel worm gear band to secure pipes larger than 2" diameter
is acceptable.
MATERIALS
Bracket:
16 gauge galvanized steel
Channel clamp:
nylon, UL94 V2 flame rating
Clamp insert:
thermoplastic elastomer
LOAD RATINGS
BRACKET:
Short bracket:
250-lbs.
Long bracket:
100-lbs.
CHANNEL CLAMP:
Temp
Safe Load*
–10°F – 130°F
70 lbs.
131°F – 179°F
38 lbs.
180°F – 220°F
12 lbs.
*Safe working load = 1/2 failure of centrally hung load
DIMENSIONS
TouchDown Clamp
Short Bracket
Long Bracket
A: channel clamp post
1 "
—
—
B: channel clamp capacity
¼"-1 "
—
—
C: channel clamp base
1 "
—
—
D: pilot hole spacing (centerline)
—
1.0"
1.0"
E: all-thread hole diameter
—
0.515"
0.515"
F: bracket length
—
15.00"
26.00"
G: bracket height
—
0.465"
0.465"
H: bracket width
—
0.675"
0.675"
I: bracket pilot hole diameter
—
0.100"
0.100"
J: bracket thickness
—
16 - ga.
16 - ga.
K: bracket centerline (holes for all-thread)
—
13.00"
24.00"
523-3MSS2
7 8
7 8
3 8
3 8
3 8
1 8
Create Item Number
523-3MSAB
e.g. 523-3MSS2:
steel bracket with two channel clamps
Made in USA
L
= (26") long bracket
S
= (15") short bracket
_
= bracket only, no channel clamps
2
= bracket, two channel clamps
3
= bracket, three channel clamps
BRACKET CONFIGURATION A
B
Heavy Duty PowerBar
™
Mini Strut
A
B
C
Sioux Chief Manufacturing Company | P: 1.800.821.3944 | F: 1.800.758.5950 | www.siouxchief.com
3-14
ITEM # SUBMITTED �����������������������������������������
JOB NAME �����������������������������������������������
LOCATION �����������������������������������������������
ENGINEER �����������������������������������������������
CONTRACTOR ��������������������������������������������
PO# ������������������������ TAG ������������������������