Sioux Chief DoubleDuty Test Plug - Manual

1
4
3
2
DoubleDuty
™
Test Plug Installation
Remove drain head
O-ring contact,
+ 1 full turn only
Subfl oor
2″ pipe
O-ring makes
seal on pipe
stop
Plug holds
pressure
test
To Perform DWV pressure test
1. Be sure to check with, and
follow all local plumbing codes
during installation and testing of
drain.
Unscrew and remove drain head.
Keep head for later installation.
LUBRICATE O-RING
Use silicone stem lube, lip balm,
liquid soap, etc.
2. Align lugs on test plug (just
above o-ring) with slots in
clamping collar. Push plug
through collar.
THREAD PLUG INTO COLLAR
UNTIL O-RING CONTACTS PIPE
STOP, THEN GIVE 1 FULL TURN
ONLY - DO NOT OVERTIGHTEN
3. Set drain body to subfl oor and
solvent weld to drain piping per
typical installation procedures.
4. Perform DWV pressure test.
Plug can remain in place, to
prevent loss or damage to drain
head, and to keep debris out of
the drain line.
1
4
3
2
DoubleDuty
™
Test Plug Installation
Remove drain head
O-ring contact,
+ 1 full turn only
Subfl oor
2″ pipe
O-ring makes
seal on pipe
stop
Plug holds
pressure
test
To Perform DWV pressure test
1. Be sure to check with, and
follow all local plumbing codes
during installation and testing of
drain.
Unscrew and remove drain head.
Keep head for later installation.
LUBRICATE O-RING
Use silicone stem lube, lip balm,
liquid soap, etc.
2. Align lugs on test plug (just
above o-ring) with slots in
clamping collar. Push plug
through collar.
THREAD PLUG INTO COLLAR
UNTIL O-RING CONTACTS PIPE
STOP, THEN GIVE 1 FULL TURN
ONLY - DO NOT OVERTIGHTEN
3. Set drain body to subfl oor and
solvent weld to drain piping per
typical installation procedures.
4. Perform DWV pressure test.
Plug can remain in place, to
prevent loss or damage to drain
head, and to keep debris out of
the drain line.
1
4
3
2
DoubleDuty
™
Test Plug Installation
Remove drain head
O-ring contact,
+ 1 full turn only
Subfl oor
2″ pipe
O-ring makes
seal on pipe
stop
Plug holds
pressure
test
To Perform DWV pressure test
1. Be sure to check with, and
follow all local plumbing codes
during installation and testing of
drain.
Unscrew and remove drain head.
Keep head for later installation.
LUBRICATE O-RING
Use silicone stem lube, lip balm,
liquid soap, etc.
2. Align lugs on test plug (just
above o-ring) with slots in
clamping collar. Push plug
through collar.
THREAD PLUG INTO COLLAR
UNTIL O-RING CONTACTS PIPE
STOP, THEN GIVE 1 FULL TURN
ONLY - DO NOT OVERTIGHTEN
3. Set drain body to subfl oor and
solvent weld to drain piping per
typical installation procedures.
4. Perform DWV pressure test.
Plug can remain in place, to
prevent loss or damage to drain
head, and to keep debris out of
the drain line.
1
4
3
2
DoubleDuty
™
Test Plug Installation
Remove drain head
O-ring contact,
+ 1 full turn only
Subfl oor
2″ pipe
O-ring makes
seal on pipe
stop
Plug holds
pressure
test
To Perform DWV pressure test
1. Be sure to check with, and
follow all local plumbing codes
during installation and testing of
drain.
Unscrew and remove drain head.
Keep head for later installation.
LUBRICATE O-RING
Use silicone stem lube, lip balm,
liquid soap, etc.
2. Align lugs on test plug (just
above o-ring) with slots in
clamping collar. Push plug
through collar.
THREAD PLUG INTO COLLAR
UNTIL O-RING CONTACTS PIPE
STOP, THEN GIVE 1 FULL TURN
ONLY - DO NOT OVERTIGHTEN
3. Set drain body to subfl oor and
solvent weld to drain piping per
typical installation procedures.
4. Perform DWV pressure test.
Plug can remain in place, to
prevent loss or damage to drain
head, and to keep debris out of
the drain line.
1
4
3
2
DoubleDuty
™
Test Plug Installation
Remove drain head
O-ring contact,
+ 1 full turn only
Subfl oor
2″ pipe
O-ring makes
seal on pipe
stop
Plug holds
pressure
test
To Perform DWV pressure test
1. Be sure to check with, and
follow all local plumbing codes
during installation and testing of
drain.
Unscrew and remove drain head.
Keep head for later installation.
LUBRICATE O-RING
Use silicone stem lube, lip balm,
liquid soap, etc.
2. Align lugs on test plug (just
above o-ring) with slots in
clamping collar. Push plug
through collar.
THREAD PLUG INTO COLLAR
UNTIL O-RING CONTACTS PIPE
STOP, THEN GIVE 1 FULL TURN
ONLY - DO NOT OVERTIGHTEN
3. Set drain body to subfl oor and
solvent weld to drain piping per
typical installation procedures.
4. Perform DWV pressure test.
Plug can remain in place, to
prevent loss or damage to drain
head, and to keep debris out of
the drain line.
1
4
3
2
DoubleDuty
™
Test Plug Installation
Remove drain head
O-ring contact,
+ 1 full turn only
Subfl oor
2″ pipe
O-ring makes
seal on pipe
stop
Plug holds
pressure
test
To Perform DWV pressure test
1. Be sure to check with, and
follow all local plumbing codes
during installation and testing of
drain.
Unscrew and remove drain head.
Keep head for later installation.
LUBRICATE O-RING
Use silicone stem lube, lip balm,
liquid soap, etc.
2. Align lugs on test plug (just
above o-ring) with slots in
clamping collar. Push plug
through collar.
THREAD PLUG INTO COLLAR
UNTIL O-RING CONTACTS PIPE
STOP, THEN GIVE 1 FULL TURN
ONLY - DO NOT OVERTIGHTEN
3. Set drain body to subfl oor and
solvent weld to drain piping per
typical installation procedures.
4. Perform DWV pressure test.
Plug can remain in place, to
prevent loss or damage to drain
head, and to keep debris out of
the drain line.
1
4
3
2
DoubleDuty
™
Test Plug Installation
Remove drain head
O-ring contact,
+ 1 full turn only
Subfl oor
2″ pipe
O-ring makes
seal on pipe
stop
Plug holds
pressure
test
To Perform DWV pressure test
1. Be sure to check with, and
follow all local plumbing codes
during installation and testing of
drain.
Unscrew and remove drain head.
Keep head for later installation.
LUBRICATE O-RING
Use silicone stem lube, lip balm,
liquid soap, etc.
2. Align lugs on test plug (just
above o-ring) with slots in
clamping collar. Push plug
through collar.
THREAD PLUG INTO COLLAR
UNTIL O-RING CONTACTS PIPE
STOP, THEN GIVE 1 FULL TURN
ONLY - DO NOT OVERTIGHTEN
3. Set drain body to subfl oor and
solvent weld to drain piping per
typical installation procedures.
4. Perform DWV pressure test.
Plug can remain in place, to
prevent loss or damage to drain
head, and to keep debris out of
the drain line.
1
4
3
2
DoubleDuty
™
Test Plug Installation
Remove drain head
O-ring contact,
+ 1 full turn only
Subfl oor
2″ pipe
O-ring makes
seal on pipe
stop
Plug holds
pressure
test
To Perform DWV pressure test
1. Be sure to check with, and
follow all local plumbing codes
during installation and testing of
drain.
Unscrew and remove drain head.
Keep head for later installation.
LUBRICATE O-RING
Use silicone stem lube, lip balm,
liquid soap, etc.
2. Align lugs on test plug (just
above o-ring) with slots in
clamping collar. Push plug
through collar.
THREAD PLUG INTO COLLAR
UNTIL O-RING CONTACTS PIPE
STOP, THEN GIVE 1 FULL TURN
ONLY - DO NOT OVERTIGHTEN
3. Set drain body to subfl oor and
solvent weld to drain piping per
typical installation procedures.
4. Perform DWV pressure test.
Plug can remain in place, to
prevent loss or damage to drain
head, and to keep debris out of
the drain line.