Installation, Installing antenna – DAVIS Cellular Telephone Antenna Kit User Manual
Page 11
Installation
Page 11
I
NSTALLATION
Follow the instructions below to install the various components of your CTM.
In many cases, you will need to use the installation manual supplied with the
component for specific instructions.
Note:
Before beginning the installation, disconnect the cables attached in order to configure the CTM.
Installing Antenna
You may mount the antenna on either the Sensor Mounting Arm or on a pipe,
post, or wall using the Antenna Mounting Bracket (#7684).
✦
Installing on Sensor Mounting Arm (SMA)
Attach the antenna to the ground plane as shown below; screw on until
snug. Attach the ground plane to the SMA using the #8-32 x
¾
" screws,
flat washers, split lock washers, and hex nuts as shown below.
Note:
It may be necessary to drill one or two holes in the SMA to accommodate the antenna/
ground plane assembly. If so, use the holes in the ground plane as a guide and drill holes
using a 7/32" (5.5mm) drill bit.
If necessary, drill holes using
7/32" (5.5 mm) drill bit.
Antenna
Ground
Plane
8-32 x 3/4" Screw
Flat Washer
Flat Washer
Lock Washer
#8 Hex Nut
Ground Plane
Sensor Mounting Arm
- Envoy8X Getting Started Guide (16 pages)
- Vantage Pro2 Long Range Repeater Installation Addendum (16 pages)
- Wireless Temperature Station (6372) Installation Manual (12 pages)
- Solar Power Kit For Vantage Weather Stations and Envoy8X (8 pages)
- Energy EnviroMonitor: Console (63 pages)
- EZ-Mount Installation (16 pages)
- Gro/Energy/Health Installation (24 pages)
- GroWeather Console (65 pages)
- GroWeather/EnviroMonitor: Systems Installation (24 pages)
- Health EnviroMonitor: Console (60 pages)
- Anemometer (7911, 7914) (8 pages)
- Rain Collector II for GroWeather, EnviroMonitor, Weather Monitor and Wizard (16 pages)
- Sensor - UV for GroWeather or EnviroMonitor (16 pages)
- Solar Radiation Sensor for GroWeather and EnviroMonitor (16 pages)
- Temperatur/Humidity Sensor for GroWeather, EnviroMonitor, & Weather Monitor (12 pages)
- Temperature Sensor/Probe for GroWeather, EnviroMon., Weather Monitor/Wizard (4 pages)
- GroWeatherLink Software (108 pages)
- GroWeatherLink/ET Data Logger (2 pages)
- Short-Range Modem Pair: Perception, GroWeather, EnviroMon., Monitor, Wizard (8 pages)
- Alarm Output Module (16 pages)
- Cable Coupler Kit (4 pages)
- Cable Crimp-Type Splice Connector (4 pages)
- Complete System Shelter (12 pages)
- Fan-Aspirated Radiation Shield (24 pages)
- Grounding Kit (4 pages)
- Interface Cable Adapter Module (8 pages)
- Mounting Pole Kit Installation (4 pages)
- Mounting Tripod Kit (8 pages)
- Multi-purpose Shelter (12 pages)
- Radiation Shield (7714) (16 pages)
- Radio Surge Protector (4 pages)
- Rain Collector Heater (12 pages)
- Rain Collector Shelf: GroWeather, EnviroMonitor, Weather Monitor & Wizard (8 pages)
- Second Solar Panel for EZ-Mount Solar Power Kit (4 pages)
- Sensor Mounting Arm for GroWeather, EnviroMonitor, Weather Monitor & Wizard (16 pages)
- Sensor Tilting Bracket for GroWeather or EnviroMonitor (8 pages)
- Shelter Heaters (12 pages)
- Solar Power Kit for Non-Vantage Pro Stations (16 pages)
- Surge Protector (2 pages)
- Surge Protector Shelter - Large (8 pages)
- Surge Protector Shelter - Small (4 pages)
- Terminal Box for sensors/interface module, communication lines: GroWeather (8 pages)
- WeatherLink for Windows 4.0 (116 pages)
- WeatherLink Getting Started Guide (20 pages)
- WeatherLink Mac OS X Getting Started Guide (16 pages)