HP ProLiant DL380 G5 Server User Manual
Page 70
•
Other—The system does not support Advanced Memory Protection or the Management Agent cannot determine
the status.
•
Not Protected—This system supports Advanced Memory Protection but the feature is disabled.
•
Protected—The system supports Advanced Memory Protection. The feature is enabled but not engaged.
•
Degraded—The system was protected, but the Advanced Memory Protection has been engaged; therefore
Advanced Memory Protection is no longer available.
•
DIMMECC—The system is protected via DIMM ECC only.
•
mirrorNoFaults—The system is protected by Advanced Memory Protection in the mirrored mode. No DIMM
faults have been detected.
•
mirrorWithFaults—The system is protected by Advanced Memory Protection in the mirrored mode. One or more
DIMM faults have been detected.
•
hotSpareNoFaults—The system is protected by Advanced Memory Protection in the hot spare mode. No DIMM
faults have been detected.
•
hotSpareWithFaults—The system is protected by Advanced Memory Protection in the hot spare mode. One or
more DIMM faults have been detected.
•
xorNoFaults—The system is protected by Advanced Memory Protection in the XOR memory mode. No DIMM
faults have been detected.
•
xorWithFaults—The system is protected by Advanced Memory Protection in the XOR memory mode. One or
more DIMM faults have been detected.
•
advancedEcc—The system is protected by Advanced Memory Protection in the Advanced ECC mode.
•
Advanced Memory Protection Types Available—Displays the options available.
•
XOR—This system is configured for Advanced Memory Protection using the XOR engine.
•
Mirrored memory with dual memory boards—This system is configured for Mirrored Advanced Memory
Protection within a dual memory board configuration. The mirrored memory may be swapped with memory on
the same memory board or with memory on the second memory board.
•
Mirrored Memory within a single memory board—This system is configured for Mirrored Advanced Memory
Protection within a single memory board.
•
Advanced ECC—This system is configured for the Advanced ECC type of Advanced Memory Protection
•
Mirrored (deprecated)—This system is configured for Mirrored Advanced Memory Protection
•
Online Spare—This system is configured for Online Spare Advanced Memory Protection.
•
Advanced Memory Protection Type Active—displays the currently active type of Advanced Memory Protection
based on the types available. The following connection states are supported:
•
Other—The Management Agent cannot determine the Advanced Memory Protection fault tolerance. You may
need to upgrade your software.
•
None—This system is not configured for Advanced Memory fault tolerance.
•
Online Spare Memory— A single spare bank of memory is set-aside at boot time. If enough ECC errors occur,
the spare memory is activated and the memory experiencing the errors is disabled.
•
Mirrored Memory—This system is configured for Mirrored Memory Protection. All memory banks are duplicated
in Mirrored Memory, as opposed to only one for Online Spare Memory. If enough ECC errors occur, the spare
memory is activated and the memory experiencing the errors is disabled.
•
XOR—This system is configured for Advanced Memory Protection using the XOR engine.
•
Memory Board—The slot in which the memory board or cartridge is installed.
•
Other—The value is unsupported or could not be determined.
•
Present—The board or cartridge has memory and is currently online.
•
Absent—The board or cartridge is offline.
•
Board Status—This provides the current status of the Advanced Memory Protection memory board or cartridge.
The following status values are supported:
•
Other—The condition of this memory board or cartridge could not be determined.
•
OK—The memory board or cartridge is operating normally.
•
Degraded—The memory board or cartridge is in an error state. Check for correct memory installation and
that the board has been inserted properly.
•
Total Board Memory—This value specifies the size of memory for this board or cartridge, including memory
seen by the OS and the memory used for spare, mirrored, or XOR configurations.
•
Memory in Use—This value specifies the size of memory for this board or cartridge as seen by the OS.
Agent information 70