AMX TPI-PRO-2 - Manual (Page 98)

Programming
92 TPI-PRO Total Presentation Interface - Pro Edition
"^" Button Commands (Cont.)
^BMF
Set any/all button
parameters by
sending
embedded codes
and data.
Syntax:
"'^BMF-,,'"Variables:variable text address char array = 1 - 4000.button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons 1 = Off state and 2 = On state).level range = 1 - 600 (level value is 1 - 65535).data:’%B’ = Set the border style name. See the Border styles table on page 84.’%B’, = Set the borer style number. See the Border styles table on
page 84.’%DO<1-5><1-5><1-5><1-5><1-5> = Set the draw order. Listed from bottom to top.
Refer to the ^BDO command on page 89 for more information.’%F’, = Set the font. See the Default Font Styles and ID
Numbers table on page 83.’%F’ = Set the font. See the Default Font Styles and ID
Numbers table on page 83.’%MI’ = Set the mask image. Refer to the ^BMI command on page 94 for
more information.’%T’ = Set the text using ASCII characters (empty is clear).’%P’ = Set the picture/bitmap filename (empty is clear).’%I’, = Set the icon using values of 1 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).’%I’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).’%J’, = As shown the following telephone keypad alignment chart: ’%JT’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,,’’%JB’ = As shown the above telephone keypad
alignment chart BUT the 0 (zero) is absolute and followed by ’,,’’%JI’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,,’1478963250Zero can be used for an absolute position
Variables:
variable text address char array = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
level range = 1 - 600 (level value is 1 - 65535).
data:
’%B’ = Set the border style name. See the Border styles table on page 84.
’%B’, = Set the borer style number. See the Border styles table on
page 84.
’%DO<1-5><1-5><1-5><1-5><1-5> = Set the draw order. Listed from bottom to top.
Refer to the ^BDO command on page 89 for more information.
’%F’, = Set the font. See the Default Font Styles and ID
Numbers table on page 83.
’%F’ = Set the font. See the Default Font Styles and ID
Numbers table on page 83.
’%MI’ = Set the mask image. Refer to the ^BMI command on page 94 for
more information.
’%T’ = Set the text using ASCII characters (empty is clear).
’%P’ = Set the picture/bitmap filename (empty is clear).
’%I’, = Set the icon using values of 1 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).
’%I’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).
’%J’, = As shown the following telephone keypad alignment chart:
’%JT’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,,’
’%JB’ = As shown the above telephone keypad
alignment chart BUT the 0 (zero) is absolute and followed by ’,,’
’%JI’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,,’
1
4
7 8 9
6
3 2
5
0
Zero can be used for an absolute position