AMX TPI-PRO-2 - Manual (Page 103)

Programming
97 TPI-PRO Total Presentation Interface - Pro Edition
^BRD
Set the border of
a button state/
states.
This command works only if the specified border is not the same as the current border.
The border names are available through the TPDesign4 border-name drop-down list.
Syntax:
"'^BRD-,,'"Variable:variable text address range = 1 - 4000.button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons 1 = Off state and 2 = On state).border name = Refer to the Border styles table on page 84.Example:SEND_COMMAND Panel,"'^BRD-500.504&510.515,1&2,Quad Line'"Sets the border by name (Quad Line) to those buttons with the variable text range of
500-504 & 510-515.Refer to the TPD4 Border Styles by Name table on page 84.^BSFSet the focus to
the text area. Note: Select one button at a time (single variable text address). Do not assign a variable
text address range to set focus to multiple buttons. Only one variable text address can be
in focus at a time.Syntax:"'^BSF-,'"Variable:variable text address = 1 - 4000.selection value = unselect = 0 and select = 1.Example:SEND_COMMAND Panel,"'^BSF-500,1'"Sets the focus to the text area of the button. ^BSMSubmit text for
text area buttons.This command causes the text areas to send their text as strings to the NetLinx Master.Syntax:"'^BSM-'"Variable:variable text address range = 1 - 4000.Example:SEND_COMMAND Panel,"'^BSM-500'"Submits the text of the text area button.^BSOSet the sound
played when a
button is pressed.If the sound name is blank the sound is then cleared. If the sound name is not matched,
the button sound is not changed.Syntax:"'^BSO-,,'"Variable:variable text address range = 1 - 4000.button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons 1 = Off state and 2 = On state).sound name = (blank - sound cleared, not matched - button sound not changed).Example:SEND_COMMAND Panel,"'^BSO-500,1&2,music.wav'"Assigns the sound 'music.wav' to the button Off/On states."^" Button Commands (Cont.)
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
border name = Refer to the Border styles table on page 84.
Example:
SEND_COMMAND Panel,"'^BRD-500.504&510.515,1&2,Quad Line'"
Sets the border by name (Quad Line) to those buttons with the variable text range of
500-504 & 510-515.
Refer to the TPD4 Border Styles by Name table on page 84.
^BSF
Set the focus to
the text area.
Note: Select one button at a time (single variable text address). Do not assign a variable
text address range to set focus to multiple buttons. Only one variable text address can be
in focus at a time.
Syntax:
"'^BSF-,'"
Variable:
variable text address = 1 - 4000.
selection value = unselect = 0 and select = 1.
Example:
SEND_COMMAND Panel,"'^BSF-500,1'"
Sets the focus to the text area of the button.
^BSM
Submit text for
text area buttons.
This command causes the text areas to send their text as strings to the NetLinx Master.
Syntax:
"'^BSM-'"
Variable:
variable text address range = 1 - 4000.
Example:
SEND_COMMAND Panel,"'^BSM-500'"
Submits the text of the text area button.
^BSO
Set the sound
played when a
button is pressed.
If the sound name is blank the sound is then cleared. If the sound name is not matched,
the button sound is not changed.
Syntax:
"'^BSO-,
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
sound name = (blank - sound cleared, not matched - button sound not changed).
Example:
SEND_COMMAND Panel,"'^BSO-500,1&2,music.wav'"
Assigns the sound 'music.wav' to the button Off/On states.
"^" Button Commands (Cont.)