Yokogawa FVX110 User Manual

User’s manual fvx110 fieldbus segment indicator

background image

User’s

Manual

FVX110

Fieldbus Segment Indicator

IM 01S01C01-01EN

IM 01S01C01-01EN

2nd Edition

Table of contents

Document Outline

Contents
1. Introduction
-  Regarding This Manual
- 1.1 Safe Use of This Product
- 1.2 Warranty
- 1.3 ATEX Documentation
2. Handling Cautions
- 2.1 Model and Specifications Check
- 2.2 Unpacking
- 2.3 Storage
- 2.4 Selecting the Installation Location
- 2.5 Waterproofing of Cable Conduit Connections
- 2.6 Restrictions on Use of Radio Transceivers
- 2.7 Insulation Resistance and Dielectric Strength Test
- 2.8 Installation of an Explosion-Protected Instrument
3. Component Names
4. About Fieldbus
- 4.1 Outline
- 4.2 Internal Structure of FVX110
  - 4.2.1 System/network Management VFD
  - 4.2.2 Function Block VFD
- 4.3 Logical Structure of Each Block
- 4.4 Wiring System Configuration
5. Installation
- 5.1 Precautions
- 5.2 Mounting
- 5.3 Wiring
  - 5.3.1 Wiring Precautions
  - 5.3.2 Wiring Installation
- 5.4 Grounding
- 5.5 Connection of Devices
- 5.6 Host Setting
- 5.7 Bus Power ON
- 5.8 Integration of DD
- 5.9 Set the Parameters Using DTM
- 5.10 Continuous Record of Values
- 5.11 Generation of Alarm
6. Configuration
- 6.1 Network Design
- 6.2 Network Definition
- 6.3 Definition of Combining Function Blocks
- 6.4 Setting of Tags and Addresses
- 6.5 Communication Setting
  - 6.5.1 VCR Setting
  - 6.5.2 Function Block Execution Control
- 6.6 Block Setting
7. Explanation of Basic Items
- 7.1 Outline
- 7.2 Setting and Changing Parameters for the Whole Process
- 7.3 LCD Transducer Block
8. Explanation of Basic Items (switching displays)
- 8.1 Single Scroll Mode
- 8.2 Continuous Scroll Mode (scan mode)
- 8.3 Direction of Display Switching
9. In-Process Operation
- 9.1 Mode Transition
- 9.2 Generation of Alarm
- 9.3 Device Diagnostic Simulation Function
- 9.4 Write lock (Write-protect) function
10. Maintenance
- 10.1 Overview
- 10.2 Disassembly and Reassembly
  - 10.2.1 Replacing the display
  - 10.2.2 Replacing the CPU Board Assembly
11. Device Information
- 11.1 DEVICE STATUS
- 11.2 Status of Each Parameter in Failure Mode
12. Parameter Lists
- 12.1 Resource Block
- 12.2 LCD Transducer Block
13. General Specifications
- 13.1 Functional Specifications
- 13.2 Physical Specifications
- 13.3 Model and Suffix Codes
- 13.4 Optional Specifications (For Explosion Protected type)
- 13.5 Optional Specifications
- 13.6 Dimensions
Appendix 1. Signal Characterizer (SC) Block
- A1.1 Schematic Diagram of Signal Characterizer Block
- A1.2 Input Section
  - A1.2.1 Determining the Mode
  - A1.2.2 Judging BLOCK_ERR
- A1.3 Line-segment Factor Determination Section
  - A1.3.1 Conditions for Configuring Valid Coefficients (CURVE_X, CURVE_Y)
- A1.4 List of Signal Characterizer Block Parameters
- A1.5 Application Example
Appendix 2. Integrator (IT) Block
- A2.1 Schematic Diagram of Integrator Block
- A2.2 Input Process Section
- A2.3 Adder
  - A2.3.1 Status of Value after Addition
  - A2.3.2 Addition
- A2.4 Integrator
- A2.5 Output Process
- A2.6 Reset
- A2.7 List of Integrator Block Parameters
Appendix 3. Input Selector (IS) Block
- A3.1 Input Selector Function Block Schematic
- A3.2 Input Section
  - A3.2.1 Mode Handling
  - A3.2.2 MIN_GOOD Handling
- A3.3 Selection
  - A3.3.1 OP_SELECT Handling
  - A3.3.2 SELECTION Handling
- A3.4 Output Processing
- A3.5 List of Input Selector Block Parameters
- A3.6 Application Example
Appendix 4. Arithmetic (AR) Block
- A4.1 Arithmetic Function Block Schematic
- A4.2 Input Section
- A4.3 Computation Section
- A4.4 Output Section
  - A4.4.1 Mode Handling
  - A4.4.2 Status Handling
- A4.5 List of the Arithmetic Block Parameters
Appendix 5. PID Block
- A5.1 Function Diagram
- A5.2 Functions of PID Block
- A5.3 Parameters of PID Block
- A5.4 PID Computation Details
  - A5.4.1 PV-proportional and -derivative Type PID (I-PD) Control Algorithm
  - A5.4.2 PID Control Parameters
- A5.5 Control Output
  - A5.5.1 Velocity Type Output Action
- A5.6 Direction of Control Action
- A5.7 Control Action Bypass
- A5.8 Feed-forward
- A5.9 Block Modes
  - A5.9.1 Mode Transitions
- A5.10 Bumpless Transfer
- A5.11 Setpoint Limiters
  - A5.11.1 When PID Block Is in Auto Mode
  - A5.11.2 When PID Block Is in Cas or RCas Mode
- A5.12 External-output Tracking
- A5.13 Measured-value Tracking
- A5.14 Initialization and Manual Fallback (IMan)
- A5.15 Manual Fallback
- A5.16 Auto Fallback
- A5.17 Mode Shedding upon Computer Failure
  - A5.17.1 SHED_OPT
- A5.18 Alarms
  - A5.18.1 Block Alarm (BLOCK_ALM)
  - A5.18.2 Process Alarms
- A5.19 Example of Block Connections
- A5.20 View Object for PID Function Block
Appendix 6. Multiple Analog Output (MAO) Block
- A6.1 Function Block Diagram
- A6.2 Block Mode
- A6.3 Fault State
- A6.4 Status Transitions
- A6.5 Parameter list display
Appendix 7. Link Master Functions
- A7.1 Link Active Scheduler
- A7.2 Link Master
- A7.3 Transfer of LAS
- A7.4 LM Functions
- A7.5 LM Parameters
  - A7.5.1 LM Parameter List
  - A7.5.2 Descriptions for LM Parameters
- A7.6 FAQs
Appendix 8. Software Download
- A8.1 Benefits of Software Download
- A8.2 Specifications
- A8.3 Preparations for Software Downloading
- A8.4 Software Download Sequence
- A8.5 Download Files
- A8.6 Steps after Activating a Field Device
- A8.7 Troubleshooting
- A8.8 Resource Block’s Parameters Relating to Software Download
- A8.9 System/Network Management VFD Parameters Relating to Software Download
- A8.10 Comments on System/Network Management VFD Parameters Relating to Software Download
Revision Information