Climax FF8200 FLANGE FACER - Manual (Page 2)

US Metric
Climax Portable Machining & Welding Systems Web site: climaxportable.com
Worldwide Phone:
1.503.538.2185 N. America Toll-Free: 1.800.333.8311 Fax: 1.503.538.7600 E-mail: [email protected]
page 2
SpeciFicationS
All dimensions should be considered reference. Contact your Climax Representative for precision dimensions. Specifications are subject to change without notice. There are no systems or components
on this machine that are capable of producing hazardous EMC, UV or other radiation hazards. The machine does not use lasers nor does it create hazardous materials such as gasses or dust.
Machine Performance Ranges
ID: Mounting range 45 - 120 inches 1143.0 - 3048.0 mm
Facing diameter range 45 - 120 inches 1143.0 - 3048.0 mm
Milling diameter range 45 - 120 inches 1143.0 - 3048.0 mm
Grinding diameter range 45 - 120 inches 1143.0 - 3048.0 mm
Swing diameter @ minimum 84.7 inches 2151.4 mm
with feedbox on end of arm
Radial tool slide travel 12 inches 304.8 mm
Axial tool head travel 4 inches 101.6 mm
Depth required inside bore for ID chuck 12.13 ± 0.25 inches 308.1 ± 6.4 mm
(± 0.25 inches (± 6.4 mm) is travel of leveling foot)
Feed Rate 0.002 - 0.040 in/rev 0.051 - 1.016 mm/rev
OD: Mounting range * 89.8 - 136.4 inches 2280.9 - 3464.6 mm
Facing diameter range 45 - 120 inches 1143.0 - 3048.0 mm
Milling diameter range 45 - 113.5 inches 1143.0 - 2882.9 mm
Grinding diameter range (w/ feed box) 45 - 118 inches 1143.0 - 2997.2 mm
Grinding diameter range (w/o feed box) 45 - 120 inches 1143.0 - 3048.0 mm
Refer to ID for specifications not listed
Milling Option:
Vertical Stroke, milling head 8 inches 203.2 mm
Rotational Drive System
Drive type Pneumatic or hydraulic drive with
pinion and internal ring gear
Pinion gear to ring gear reduction 7.429:1
Single point turning speed range:
Pneumatic 5 - 29 RPM
Hydraulic (based on motor choice) 1.8 - 18 RPM
Milling & grinding speed ranges (with reducer):
Pneumatic 0.004 - 0.173 RPM
(rapid only, not in cut) (58 ipm @ 72 inch dia.) (1473.2 mm/min @ 1828.8 mm dia.)
Hydraulic (based on motor choice) 0.002 - 0.374 RPM
Power input requirements
Pneumatic - 3.5 Hp (2.6 kW) 50 ft³/min @ 90 psi 1.42 m³/min @ 620 kPa
Hydraulic 10 gpm@1200 psi 37.9 L/min @ 8273 kPa
Measures
For machine dimensions, please refer to dimensional drawings
ID machine weight, approximate 4000 lb 1814.4 kg
ID machine weight with mill, approximate 4150 lbs 1882.4 kg
OD machine weight, approximate 3775 lb 1712.3 kg
ID machine weight with mill, approximate 3925 lbs 1780.4 kg
Chuck crate dimensions, (for ID and OD machines) (WxDxH)
Wood, approx. 93 x 40.5 x 40 in 2362 x 1029 x 1016 mm
Metal, approx. 90.2 x 40.2 x 36.2 in 2291 x 1021 x 920 mm
Leg crate dimensions (for ID and OD machines) (WxDxH)
Wood, approx. 94 x 43.5 x 19 in 2388 x 1105 x 483 mm
Metal, approx. 94.2 x 42.7 x 19.2 in 2393 x 1085 x 488 mm
OD mount hardware crate dimensions (for OD machine only) (WxDxH)
Wood, approx. 94 x 43.5 x 19 in 2388 x 1105 x 483 mm
Metal, approx. 94.2 x 42.7 x 19.2 in 2393 x 1085 x 488 mm
Testing Data
Flatness at 82 inch (2083 mm) diameter: .0068 inches (0.17 mm)
On a dedicated fixture made of A-36 steel in a controlled environment with single point machine, after warm-up.
* OD mount minimum arm swing is 84.7 inches (2151.4 mm) diameter. An additional customer supplied structure will be required to chuck below the minimum swing
diameter with the feedbox attached..