Extron Electronics MLS 608 D Series User Guide User Manual
Page 80
Command
ASCII Command
(host to switcher)
Response
(switcher to host)
Additional
Description
EDID Management
Assign EDID data to
inputs (analog and
digital inputs)
E
AX2@*X2!EDID}
EdidAX2@*X2!]
Assign EDID data X2!
to inputs VGA or HDMI
X2@
View EDID data
assigned
E
AX2@EDID}
X2!]
View EDID data
assignment.
Save an output
EDID to (analog)
user loaded space
E
SX2#*X2$EDID}
EdidSX2#*X2$]
Save display EDID to
analog user space.
Save an output
EDID to (digital)user
loaded space
E
SX2#*X2%EDID}
EdidSX2#*X2%]
Save display EDID to
digital user space.
View/read EDID in
hex format
E
RX2@EDID}
X2&]
View EDID data in hex
format for X2@.
View EDID native
resolution
E
NX2@*X2^EDID}
X2*]
View native resolution
and refresh rate.
HDCP Management
View input HDCP
status
E
IX2(HDCP}
X3!]
Signal present, HDCP,
non HDCP, or HDCP
status unknown.
View output HDCP
E
OHDCP}
X3@]
Output connected,
HDCP, non HDCP, or
HDCP status unknown.
View HDCP status
for all HDMI inputs
E
I*HDCP}
X3!
5
*X3!
6
*X3!
7
*X3!
8
]
HDCP, non HDCP, or
HDCP status unknown
(for all HDMI inputs).
Set HDCP
notification
E
NX3#HDCP}
HdcpNX3#]
Show green or black
screen.
View HDCP
notification setting
E
NHDCP}
X3#]
NOTE:
X2! = DDC value (EDID).
See EDID table on page 66 for details
.
X2@ = Video group: 1 = VGA, 2 = HDMI
X2# = Output selection: 1 = analog buffered VGA connector on MLS 608 D, 2 = digital HDMI connector on
MTP/HDMI U R
X2$ = Analog EDID user definable locations: 49 = user 1, 50 = user 2
X2% = Digital EDID user definable locations: 51 = user 3, 52 = user 4
X2^ = EDID, 0 = current assigned EDID: 1 = user loaded 49 when X2@ = 1, user loaded 51 when X2@ = 2;
2 = user loaded 50 when X2@ = 1, user loaded 52 when X2@ = 2
X2& = 128 or 256 byte EDID raw hex (text form)
X2* = Native resolution and refresh rate, for example 1280x720@60
X2( = Inputs 5 through 8 only (for HDCP commands)
X3! = Input HDCP status: 0 = source is connected but not HDCP compliant, 1 = source is connected and is HDCP
compliant, 2 = no source connected, 3 = HDCP status not known
X3@ = Output HDCP status: 0 = output is connected, current input source encrypted, output is not HDCP compliant,
1 = output is connected, current input source encrypted, output is HDCP compliant, 2 = no output connected,
3 = output is connected, current input source is not encrypted or not connected, output HDCP status not known
X3# = HDCP notification = green screen notification on the output when a display is non-HDCP compliant: 0 = black,
1 = green (default)
MLS 608 D Series • SIS Programming and Control
74