Extron Electronics ISS 108 - Manual (Page 49)

4-3 Integration Seamless Switcher • Programmer’s Guide
Ethernet connection
The cable can be terminated as either a patch cable or a crossover cable (figure 4-2)
and must be properly terminated for your application:
• Patch (straight) cable — Connection of the ISS to an Ethernet hub, router, or
switcher that also hosts a controlling computer.
• Crossover cable — Direct connection between the ISS and a computer.
Default address
To access the switcher via the Ethernet port, you will need the switcher’s IP
address. If the address has been changed to an address comprised of words and
characters, the actual numeric IP address can be determined using the front panel
(see IP information in chapter 3, Operation) or the Ping utility (see Ping to determine the
switcher’s IP address or Ping to determine the Web IP address in appendix A, Ethernet
Connection, for more details). If the address has not been changed, the factory-
specified default is 192.168.254.254.
Symbols
Symbols (
X n
values), defined below, are used throughout the discussions of the
switcher-initiated messages that begin on the next page and the command/
response table that begins on page 4-9. The symbols represent variables in the
switcher-initiated messages and the command/response table fields.
= CR/LF (carriage return/line feed) (hex 0D 0A)
= CR (no line feed)
• = Space
Esc = Escape key
X1 = Input number 1 through 8
X2 = Output number 1 (program) or 2 (preview)
X3 = 0 = off, 1 = on
X4 = Take level: 0 = video and audio, 1 = video, 2 = audio
X5 = Video type:
0 = RGB 5 = Betacam 60
1 = RGBcvS 6 = HDTV
2 = YUVi 7 = S-video
3 = YUVp 8 = Composite
4 = Betacam 50
X6 = Switcher resolution:
00 = 640x480 08 = 1360x765
01 = 800x600 09 = 1365x1024
02 = 832x624 10 = 720p*
03 = 848x480 11 = 1080p
04 = 852x480 12 = 1080i
05 = 1024x768* 13 = 1400 x 1050
06 = 1280x768* 14 = 576p
07 = 1280x1024*
Native DVI resolution.
X7 = Video refresh rate:
0 = 50 Hz 3 = 75 Hz
1 = 56 Hz 4 = 85 Hz
2 = 60 Hz 5 = AFL*
Lock or AFL is Accu-RATE Frame Lock ™
(PAL = 50 Hz, NTSC =59.94 Hz).
X8 = Output video type: 0 = RGBHV, 1 = RGBS
X9 = Output sync polarity:
0 = H–/V– 2 = H+/V–
1 = H–/V+ 3 = H+/V+
X10 = Color value (0 thru 127)
X11 = Tint value (0 thru 255)
X12 = Brightness and contrast value (0 thru 63)
X13 = Size value (range depends on the resolution)
X14 = Centering value (range depends on the resolution)
X15 = Blanking value (000 thru 200)
X16 = Pixel sampling phase (000 thru 031)
X17 = Horizontal filter value (0 thru 3)
X18 = Vertical filter or composite/S-video detail filter (1 thru 7)
X19 = Preset number (01 thru 03)
X20 = RGB delay/dissolve speed (00 [RGB] or 01 [dissolve] to 50)
X21 = Program/preview output selection
Prog/Prev Prog/Prev
0 = Off/Off 2 = Off/On
1 = On/Off 3 = On/On
X22 = Test pattern type (1 through 10)
01 = Color Bars 06 = alternating pixels
02 = crosshatch 07 = film aspect ratio 1.78
03 = 4x4 crosshatch 08 = film aspect ratio 1.85
04 = gray scale
09 = film aspect ration 2.35
05 = crop 10 = ramp
X23 = Gain/attenuation -24 dB to +•9 dB, each step = 1 dB
X24 = Gain value Numeric dB value, 0 to +9
X25 = Attenuation value Numeric dB value, -1 to -24
X26 = Preview switch mode: 0 = stay mode, 1 = swap mode
X27 = Frequency: nnn.nn (kHz [horizontal] or Hz [vertical])
X28 = Detected input signal standard (0 through 4)
0 = none 3 = NTSC 4.43
1 = NTSC 3.58 4 = SECAM
2 = PAL
Dash (–) = not applicable (occurs when the input is
set for RGB or progressive YUV).
X29 = “Take” effect: 00 = cut, 01 = dissolve