Extron Electronics DVS 304 Series User Guide - Manual (Page 55)

Command
ASCII (T
elnet)
(host to pr
ocessor)
URL Encoded (W
eb)
(host to pr
ocessor)
Response (pr
ocessor to host)
Additional description
Set user passwor
d 14 24
E
X3#
CU
}
W
X3#
CU
|
Ipu•
X3#
]
Set the user access passwor
d
X3#
is 4-12 alphanumeric characters.
The passwor
d is case sensitive. Special
characters (spaces or symbols) ar
e
not allowed.
NOTE:
A user passwor
d cannot be assigned if an administrator passwor
d does not exist.
Clear user passwor
d 24
E
•CU
}
W%20CU
|
Ipu•
]
This clears the user passwor
d only
.
Read user passwor
d 24
E
CU
}
WCU
|
X3#]
Set verbose mode
24
E
X2@
CV
}
W
X2@
CV
|
Vr
b
X2@]
Set verbose mode.
NOTE:
The pr
ocessor can send out unsolicited information (such as notice of a volume or input change or a change in some other setting). That is called verbose
(wor
dy) r
elationship between the pr
ocessor and a connected device. For a dir
ect RS-232/422 connection, the pr
ocessor is set for V
erbose mode by default.
When the DVS 304 is connected via Ether
net, V
erbose mode is disabled by default in or
der to r
educe the amount of communication traffic on the network.
If you want to use the V
erbose mode with a pr
ocessor connected via Ether
net, this mode must be set to On each time you r
econnect to the pr
ocessor
.
Read verbose mode
E
CV
}
WCV
|
X2@]
Read connection’
s security
level
E
CK
}
WCK
|
X5@]
Re-map port designations
Set T
elnet port map
24
E
{port #}MT
}
W
{port #}MT
|
Pmt{port #}
]
Reset T
elnet port map
24
E
23MT
}
W23
MT
|
Pmt00023
]
Set T
elnet to the default port (23)
Disable T
elnet port map
24
E
0MT
}
W0
MT
|
Pmt00000
]
Read T
elnet port map
E
MT
}
W
MT
|
{port #}
]
Set W
eb port map
24
E
{port #}MH
}
W
{port #}MH
|
Pmh{port #}
]
Reset W
eb port map
24
E
80
MH
}
W80
MH
|
Pmh00080
]
Disable W
eb port map
24
E
0MH
}
W0
MH
|
Pmh00000
]
Read W
eb port map
24
E
MH
}
W
MH
|
{port #}
]
Set W
eb port to default value of 80
NOTE:
X2@
= V
erbose/r
esponse mode
(Default = 0 for T
elnet connections; 1 for RS-232 host contr
ol). 0 = clear/none, 1 = verbose mode, 2 = tagged r
esponses for queries, 3 = verbose mode
and tagged r
esponses for queries. If tagged r
esponses ar
e enabled, all r
ead commands will r
etur
n the constant string + the data, like setting the value does (
for example command:
Esc CN } r
esponse: Ipn• x12]).
X3#
=
Passwor
d (12 characters = maximum length; no special characters ar
e allowed)
X5@
= Connection’
s security level: 0 = anonymous, 1 – 10=extended security levels 1 thru 10, 11 = user
, 12 = administrator
DVS 304 Series • SIS Communication and Control 50