Roland JV-1010 - Manual (Page 70)

70
MIDI Implementation
❍ Effect 3 (Chorus Send Level) (Controller number 93)
status 2nd byte 3rd byte
BnH 5DH vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=Chorus Send Level: 00H - 7FH (0 - 127)
* In Performance mode, the Chorus Send Level parameter of each Part will change.
❍ RPN MSB/LSB (Controller number 100,101)
status 2nd byte 3rd byte
BnH 65H mmH
BnH 64H llH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
mm=MSB of the parameter number specified by RPN
ll=LSB of the parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended
parameters whose function is defined in the MIDI specification.
When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any
order) is transmitted to specify the parameter you wish to control. Then, Data Entry
messages (Controller numbers 6 and 38) are used to set the value of the specified parameter.
Once a RPN parameter has been specified, all further Data Entry messages on that channel
are considered to apply to that specified parameter. In order to prevent accidents, when the
desired setting has been made for the parameter, it is recommended that RPN be set to Null.
This device receives the following RPNs.
RPN Data entry
MSB LSB MSB LSB Notes
00H 00H mmH - Pitch Bend Sensitivity
mm: 00H - 0CH (0 - 12 semitones)
ll: ignored (processed as 00H)
Up to 1 octave can be specified in semitone steps.
*
The Bend Range Up/Down will also be
changed.
* Not received by the Rhythm Part (Part 10).
00H 01H mmH llH Channel Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
*
In Patch mode, the Master Tune (SYSTEM)
will change.
* In Performance mode, the Fine Tune
(PERFORM) of each Part will change. When
received on the Control channel, the Master
Tune (SYSTEM) will change.
00H 02H mmH - Channel Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
*
Not received in Patch mode.
* In Performance mode, the Coarse Tune
(PERFORM/PART) of each Part will change.
7FH 7FH - - RPN null
RPN and NRPN will be set as “unspecified”.
Once this setting has been made, subsequent
Data Entry messages will be ignored. (It is not
necessary to transmit Data Entry for RPN Null
settings.
Parameter values that were previously set will
not change.
mm, ll: ignored
● Program Change
status 2nd byte
CnH ppH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
pp=Program number: 00H - 7FH (prog.1 - prog.128)
* Not received when the Receive Program Change is OFF.
* When received on the Control channel, the Performance will change.
* Not received in Performance mode when the Receive Switch (PERFORM/PART) is OFF.
● Channel Aftertouch
status 2nd byte
DnH vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=Channel Aftertouch: 00H - 7FH (0 - 127)
* Not received in Performance mode when the Receive Switch (PERFORM/PART) is OFF.
● Pitch Bend Change
status 2nd byte 3rd byte
EnH llH mmH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
mm,ll=Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
* Not received in Performance mode when the Receive Switch (PERFORM/PART) is OFF.
■ Channel Mode Messages
● All Sound Off (Controller number 120)
status 2nd byte 3rd byte
BnH 78H 00H
n=MIDI channel: 0H - FH (ch.1 - ch.16)
* When this message is received, all notes currently sounding on the corresponding
channel will be turned off.
* Not received in Performance mode when the Receive Switch (PERFORM/PART) is OFF.
● Reset All Controllers (Controller number 121)
status 2nd byte 3rd byte
BnH 79H 00H
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
* Not received in Performance mode when the Receive Switch (PERFORM/PART) is OFF.
* When this message is received, the following controllers will be set to their reset values.
Controller Reset value
Pitch Bend Change [+-]0 (center)
Polyphonic Key Pressure 0 (off)
Channel Pressure 0 (off)
Modulation 0 (off)
Breath type 0 (minimum)
Expression 127 (maximum)
However the controller will be at minimum.
Hold 1 0 (off)
Sostenuto 0 (off)
Soft 0 (off)
Hold 2 0 (off)
RPN Unset. Previously set data will not change.
NRPN Unset. Previously set data will not change.
System General purpose controller 1 0 (minimum)
System General purpose controller 2 0 (minimum)
● All Note Off (Controller number 123)
status 2nd byte 3rd byte
BnH 7BH 00H
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
* When All Note Off is received, all currently sounding notes of the corresponding
channel will be turned off. However if Hold 1 or Sostenuto are on, the sound will be held
until these are turned off.
* Not received in Performance mode if the Receive Switch (PERFORM/PART) is OFF.
● Omni Off (Controller number 124)
status 2nd byte 3rd byte
BnH 7CH 00H
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
* The same processing as when All Note Off is received will be done.
* Not received in Performance mode if the Receive Switch (PERFORM/PART) is OFF.