Sanyo CHX06052 - Manual (Page 29)

2-11
Remote Control Functions
2
5. Address Settings
When mounting the
wireless remote control
unit on a wall for use
• Before mounting the wireless remote control unit on the wall, place the unit at the mounting
position, press the ON/OFF operation button and check that the signals are received
properly.
• To remove the wireless remote control unit, disengage it by pulling it toward you.
Operating tips • Do not operate the wireless remote control unit too far away from the signal receiver.
Doing so may cause operational errors.
Make absolutely sure that the wireless remote control unit and signal receiver are both in
the same room.
• When operating the wireless remote control unit, point it directly at the signal
receiver.
A beep is heard when a signal is received properly.
• Avoid places where the wireless remote control unit will be obscured by curtains, etc.
Remove it before operation.
When a multiple number of indoor units that can be operated by the wireless remote control unit
have been installed in the same room with a multi-unit or single-unit installation, this button enables
addresses to be set in order to prevent the sending of signals to the wrong indoor unit. Each of up to
six indoor units can be controlled separately using its own wireless remote control unit by matching
the number of the address switch on the operation area of the indoor unit and the number used for
the address of its wireless remote control unit. (The indoor units cannot be controlled separately
when they are used in a flexible combination format, simultaneous operation of multi units format or
any other such format since they will all operate at the same time.)
The signal receiver has an address switch for signal reception, and the wireless remote control unit
has an address switch for signal transmission.
How to check the
addresses
When the ADDRESS button on the wireless remote control unit is pressed, the current address
appears on the wireless remote control unit’s display. The buzzer sounds if the address
displayed matches the signal receiver’s address. (The buzzer always sounds if “ALL” appears
as the address display.)
If “ALL” appears as the address display, operations can be performed irrespective of the signal
receiver’s address. Point the wireless remote control unit at the signal receiver of the unit to be
operated, and send the signal.
How to set the matching
address
Wireless remote control unit’s address setting
1. When the ADDRESS button is held down for 4 or more seconds, “
” lights on the
wireless remote control unit’s display, and the current address blinks.
2. Each time the ADDRESS button is now pressed, the address changes by one setting in the
following sequence: ALL
→
1
→
2
→
3 ...
→
6
→
ALL.
Select the setting which matches the setting of the address switch in the operation area of
the indoor unit to be operated.
3. When the SET button is now pressed, the address stops blinking and lights instead, and it
remains on the display for 5 seconds.
The buzzer sounds if the setting matches the setting of the address switch in the operation
area of the indoor unit.
When the batteries are replaced, the address setting returns to “ALL”.
Secure the installation fitting of the wireless
remote control unit using the screws.
Press.
1
2
Place here.
Installation fitting of wireless remote control unit
Procedure for installing the
wireless remote control unit
NOTE
01_XHX1252_EN.fm Page 10 Friday, April 20, 2007 3:28 PM
Slide switch This is used to set the operation mode of the indoor units and to set the flaps.
•
Depending on the indoor unit used, the operation display and airflow direction display
settings will differ as shown below.
• Use a pointed implement to change the switch position.
• When the switch position has been changed, press the ACL button.
* For details on the flap functions, refer to the operating instructions of the indoor unit used.
• Before use, check that the slide switch has been set to the position shown in the figure
above. For details on how to set the slide switch, consult your dealer.
How to install
batteries
1. Slide the cover in the direction indicated by the arrow and
remove it.
2. Install two AAA alkaline batteries. Make sure the batteries
point in the direction marked in the battery compartment.
3. Use a pointed implement to press the ACL button.
• The batteries last about a year, depending on how much
you use the wireless remote control unit. Replace the
batteries when the wireless remote control unit’s display
fails to light, or when the remote control cannot be used to
change the air conditioner’s settings.
• When the batteries are to be replaced, make sure that both
batteries are new and that the same kind of battery is used.
• Remove the batteries if the wireless remote control unit is
not going to be used for a prolonged period.
• Dispose of the used batteries at the designated location.
How to use the
wireless remote
control unit
• Point the wireless remote control unit’s transmitter at the signal receiver. If the signal is
received properly, a beep is heard. (Two beeps are heard only when operation starts up.)
• Signals can be received over a distance of approximately 26 ft. This distance is
approximate: it may be slightly more or less depending on how much charge remains in the
batteries and on other factors.
• Ensure that the signals will not be blocked by any objects positioned between the
transmitter and signal receiver.
• Avoid placing the wireless remote control unit where it will be exposed to direct sunlight or in
the direct path of the air blown out from the air conditioner, near a heating appliance, etc.
• Do not drop, throw or wash the wireless remote control unit.
• Signal reception may not be accepted in rooms with fluorescent lights that use the
electronic instantaneous lighting system (rapid start system) or inverter system. For further
details, contact your dealer.
Model which supports
different flap settings
Swing-only model No-flap model
Slide switch position
Flap display on wireless
remote control unit
With the battery cover
removed
Heat pump (with auto
cooling/heating
function)
Heat pump (without
auto cooling/heating
function)
Cooling only
Operation mode display
on wireless remote
control unit
Slide switch position
ACL
button
Cover
ACL
button
Cover
01_XHX1252_EN.fm Page 9 Friday, April 20, 2007 3:28 PM
2. Wireless Remote Controller
MiniECO-i.indb 11 2007/06/20 16:28:14