Setting the communication adaptor board, Communication adaptor (sha-ka128aab), Remote control functions – Sanyo CHX06052 User Manual

Page 135: 1) switch operation overview, 2) adaptor number setting procedure, 4) other settings

2-117

Remote Control Functions

6. Communication Adaptor (SHA-KA128AAB)

Setting the Communication Adaptor board

The switches on the board control the adaptor numbers, turn the indoor/outdoor control wire connection on and off, and control other settings.

(1) Switch operation overview

Item selection

Use the

and

DOWN

keys to find the desired item, then press the

SET

key to select.

Changing the settings

Use the

and

DOWN

keys to change the setting, then press the

SET

key to confirm.

Hold down the

HOME

key for at least two seconds to reset to the default setting

(Any settings in progress will be

lost.)

(2) Adaptor number setting procedure

Hold down the

HOME

key for at least two seconds so the initial display shows as follows:

(no.00)

After 2 seconds

(AdP.dt)

Press the

key five times so the following display appears:

(no.05)

This automatically switches to the below display after 2 more seconds. (Operation is not necessary.)

(FirSt)

Press the

SET

key so the below display appears. (Only the green monitor LED is on.)

(1.Ano.00) (Factory setting)

Hold down the

SET

key for at least 1 second so the “00” part blinks, indicating that the setting can be changed. (The green and red monitor

LEDs are both on.)

Use the

and

DOWN

keys to set the adaptor number.

For example, to set number 3, press the

key three times. The following will display:

(1.Ano.03)

Press the

SET

key for at least 1 second to confirm. (Only the green monitor LED is on.)

UP DOWN SET

HOME

7-segment LED

Home key

Monitor LED
D1: red
D2: green

Set key

Down key

Up key

(3) Setting the indoor/outdoor control wire connection on/off

Repeat steps

in section (2) “Adaptor number setting procedure” above. The following will display:

(1.Ano.03) (When the adaptor number is 3)

Press the

key once so the following display appears:

(2.Adyu.0) (Factory setting)

Hold down the

SET

key for at least 1 second so the “0” part blinks, indicating that the setting can be changed. (The green and red monitor

LEDs are both on.)

Use the

and

DOWN

keys to turn the indoor/outdoor control wire connection on or off as shown in the table below.

For example, to connect the indoor/outdoor control wire only to LINK1, press the

key once. The following display will result:

(2.AdYu.1)

Press the

SET

key for at least 1 second to confirm. (Only the green monitor LED is on.)

(4) Other settings

With the display status showing as in number

in section (2) “Adaptor number setting procedure”, press the

and

DOWN

keys to select

the setting items shown in the following table on page 2-118. Set as needed.
The setting procedure is the same as above.
(Press the

SET

key for at least 1 second, press the

and

DOWN

keys to change, then press the

SET

key at least one second to confirm.)

Note

When configuring, do not set the same adaptor number more than once.
*

Use numbers between 1 and 7 for connecting to an Intelligent Controller.

Turn the indoor/outdoor control wire connection on/off as appropriate.
(Set to “Off” for LINKs with no connection.)

For connecting the indoor/outdoor control wire to only one link, use the
“LINK1” side.

Setting value

Indoor/outdoor control wire connection

LINK1: On, LINK2: On (factory setting)

LINK1: On, LINK2: Off

LINK1: Off, LINK2: On

LINK1: Off, LINK2: Off

MiniECO-i.indb 117

2007/06/20 16:30:28