JVC LVT0858-001A - Manual (Page 19)

15
Basic Settings
1
Press SETTING.
The CONTROL buttons now work for basic
settings.
2
Press CONTROL
∞ (or 5) repeatedly until one
of the following speakers (with the current
setting)* appears.
FRNT SP (Front Speaker) : To register the front speaker size.
CNTR SP (Center Speaker): To register the center speaker size.
REAR SP (Rear Speaker) : To register the rear speaker size.
* “SML (small)” is the initial setting. If you have already
changed the setting, another size will be shown.
3
Press CONTROL
3 (or 2) to select the
appropriate speaker size.
• Each time you press the button, the speaker size changes as
follows:
LRG (Large) : Select this when the speaker size is relatively
large. (See “Notes” below.)
SML (Small) : Select this when the speaker size is relatively
small. (See “Notes” below.)
NO : Select this when you have not connected a
speaker. (Not selectable for the front speakers.)
4
Repeat steps
2
and
3
to select the appropriate
size for the other speakers.
Notes:
• Use the following criteria as reference when adjusting:
– If the size of the cone speaker unit built in your speaker is greater
than 12 cm, select “LRG (large),” and if it is smaller than 12 cm,
select “SML (small).”
• If you have selected “NO” for the subwoofer, you can only select
“LRG (large)” for the front speaker size.
• If you have selected “SML (small)” for the front speaker size, you
cannot select “LRG (large)” for the center and rear speaker sizes.
SETTING
ANALOG PR ΙΙ
SUBWFR LFE
VOL
AUTO SR
INPUT ATT
DSP
L C R
LS S RS
LPCM
DOLBY D
DTS
CONTROL
ANALOG PR ΙΙ
SUBWFR LFE
VOL
AUTO SR
INPUT ATT
DSP
L C R
LS S RS
LPCM
DOLBY D
DTS
CONTROL
Ex.: When registering the rear speaker size.
“YES” for the subwoofer and “SML” for the front, center and
rear speakers are initial settings. To get best possible sound,
change the subwoofer and speaker settings to fit your listening
conditions.
Setting the Subwoofer Information
Register whether you have connected a subwoofer or not. If you
have already connected a subwoofer, follow the procedure below.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
1 again.
1
Press SETTING.
The CONTROL buttons now work for basic
settings.
2
Press CONTROL ∞ (or 5) repeatedly until
“SUBWFR (Subwoofer)” (with the current
setting)* appears on the display.
* “YES” is the initial setting. If you have already changed the
setting, “NO” will be shown.
3
Press CONTROL
3 (or 2) to select “YES.”
• Each time you press the button, the subwoofer setting
alternates between “YES” and “NO.”
YES : Select this when you have connected a subwoofer.
The subwoofer speaker indicator ( SUBWFR ) lights
up on the display (see page 11). You can adjust the
subwoofer output level (see page 22).
NO : Select this when you have not connected or have
disconnected a subwoofer.
Remote
NOT
SETTING
CONTROL
R ΙΙ
VOL
SR
ATT
ANALOG PR ΙΙ
SUBWFR LFE
VOL
AUTO SR
INPUT ATT
DSP
L C R
LS S RS
LPCM
DOLBY D
DTS
CONTROL
Setting the Speakers
Information
To obtain the best possible effect from the Surround modes (see
page 32), register the following information after all connections are
completed.
• Speaker Size—FRNT SP, CNTR SP, REAR SP
• Speaker Distance—FRNT D, CNTR D, REAR D
• Crossover Frequency—CROSS
• Low Frequency Effect Attenuator—LFE
• Dynamic Range Compression—D.COMP
Speaker Size—FRNT SP, CNTR SP, REAR SP
Register the sizes of all the connected speakers.
• When you change your speakers, register the information about
the speakers again.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
1 again.
Remote
NOT
EN10-19.RX-E111&112RSL[B]_f 02.2.6, 7:33 PM 15