Garret, 3 table-top or shelf mounting – GarrettCom 6K32TRC User Manual
Page 39
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07)
34
www GarrettCom com
.
.
Magnum
Fiber Switch
GARRET
Magnum
PW
Managed
Switch
Magnum
1 3 5
10/100
LK
F/H
AC
10/100
LK
2 4 6
F/
AC
1 3 5
10/100
LK
F/H
AC
10/100
LK
2 4 6
F/
AC
1 3 5
10/100
LK
F/H
AC
10/100
LK
2 4 6
F/
AC
Magnum
Fiber Switch
GARRET
Magnum
PW
Managed
Switch
Magnum
1 3 5
10/100
LK
F/H
AC
10/100
LK
2 4 6
F/
AC
1 3 5
10/100
LK
F/H
AC
10/100
LK
2 4 6
F/
AC
1 3 5
10/100
LK
F/H
AC
10/100
LK
2 4 6
F/
AC
Magnum
Fiber Switch
GARRET
Magnum
PW
Managed
Switch
Magnum
1 3 5
10/100
LK
F/H
AC
10/100
LK
2 4 6
F/
AC
1 3 5
10/100
LK
F/H
AC
10/100
LK
2 4 6
F/
AC
1 3 5
10/100
LK
F/H
AC
10/100
LK
2 4 6
F/
AC
Mid-Range Mount or
5” Set-Back Bracket
Standard Flush
23” Mount Bracket
Magnum
Fiber Switch
GARRET
Magnum
PW
Managed
Switch
Magnum
1 3 5
10/100
LK
F/H
AC
10/100
LK
2 4 6
F/
AC
1 3 5
10/100
LK
F/H
AC
10/100
LK
2 4 6
F/
AC
1 3 5
10/100
LK
F/H
AC
10/100
LK
2 4 6
F/
AC
•
The 100Mb fiber segment must operate in full-duplex (FDX) mode, i.e. the
full-duplex (factory default) setting for 100Mbps fiber ports must be used,
and
•
The worst-case OPB of the fiber link must be greater than the fiber cable’s
passive Attenuation.
(Attenuation = Cable loss + LED aging loss + Insertion loss + safety factor)
3.3
Table-Top or Shelf Mounting
The Magnum 6K32T & 6K32TRC Managed Switches can be easily mounted
on a table-top or any suitable horizontal surface. They have four rubber feet to provide
stability without scratching finished surfaces.
3.3.1 Rack-mounting (for 19” RETMA racks), Magnum 6K32T &
6K32TRC’s
Installation of a Magnum 6K32T & 6K32TRC Fiber Switch in a 19” rack is a
simple procedure. The units are 1U (1.70”) high. When properly installed, the front-
mounted LED status indicators should be in plain view and easy to read.
Rack-mount installation requires
special 19” rack-mounted
brackets and screws (included
with each Magnum 6K32T &
6K32TRC unit). These brackets
attach to the front sides of the
Fig 3.3.1 Dual Side-Mountings for
Magnum 6K32T & 6K32TRC
units
Switch (regular package, not the
Reverse version), which is then
typically fastened into a standard
19” RETMA rack as shown here
The 23” brackets and the ETSI
(European metric, approx. 21”) brackets are also available (optional) for rack-mounting
Magnum
Fiber Switch
GARRET
Magnum
PW
Managed
Switch
Magnum
1 3 5
10/100
LK
F/H
AC
10/100
LK
2 4 6
F/
AC
1 3 5
10/100
LK
F/H
AC
10/100
LK
2 4 6
F/
AC
1 3 5
10/100
LK
F/H
AC
10/100
F
1
F/
AC