GTO GP-SW050 - Manual (Page 30)

27
setting Dual gate sequence
GP-SW050 operators come from the factory with the #2 DIP switches set to OFF. DIP Switches must be changed to
accommodate dual gate operation. The information below shows the proper settings for a dual gate application.
1
2
3
4
O
N
LOCK
COM
COM
COM
ALARM
CYCLE
SAFETY
SHADOW
OPEN
CLOSE
STOP
OPEN
EDGE
CLOSE
EDGE
STATUS
STALL FORCE ADJUST
LIMIT ADJUSTMENTS
DUAL
LINK
GTO LOOP DETECTORS
LIMIT SENSORS
DIAG.
PORT
BLDC SPEED CONTROL EXIT SHADOW SAFETY
AT OPEN
LIMIT
PRISON
MODE
RUNNING
OPTIONS
TEST SWITCHES
CLOSE STOP OPEN
GTO Inc. Tallahassee, FL
SX4000 Logic Board Rev. E
MIN MAX MIN MAX OFF 120
<<< JOG >>>
<<< >>>
SET
LIMIT
CLOSED
LED11
LED10
LED09
+ ACC. PWR.
12VDC
- 300ma
W1
CUT TO USE
3 BUTTON
STATION
AUTO CLOSE
TIMER
MODE 1
MODE 2
OPEN DIR.
SLV OPN
DUAL MODE
LOW BATT
ON
ON
>>>
SIMUL
SLAVE
SECURE
OFF
OFF
<<<
DELAY
MASTER
SAFE
CYCLE
SAFETY
OPEN EDGE
RUN 2
OPEN
CLOSE
STOP
COM
COM
COM
SHADOW
LOOP
REL
AY OUTPUT
S
LOCK N.C.
LOCK COM
LOCK N.O.
RUN 1
RUN 2
CLOSED 1
CLOSED 2
1
2
3
4
O
N
LOCK
ALARM
CYCLE
SAFETY
SHADOW
OPEN
EDGE
STATUS
STALL FORCE ADJUST
DUAL
LINK
GTO LOOP DETECTORS
LIMIT SENSORS
DIAG.
PORT
BLDC SPEED CONTROL EXIT SHADOW SAFETY
AT OPEN
LIMIT
PRISON
MODE
RUNNING
OPTIONS
<<< >>>
CLOSED
LED11
LED10
LED09
+ ACC. PWR.
12VDC
- 300ma
AUTO CLOSE
TIMER
MODE 1
MODE 2
OPEN DIR.
SLV OPN
DUAL MODE
LOW BATT
ON
ON
>>>
SIMUL
SLAVE
SECURE
OFF
OFF
<<<
DELAY
MASTER
SAFE
CYCLE
SAFETY
OPEN EDGE
RUN 2
OPEN
CLOSE
STOP
COM
COM
COM
SHADOW
LOOP
REL
AY OUTPUT
S
LOCK N.C.
LOCK COM
LOCK N.O.
RUN 1
RUN 2
CLOSED 1
CLOSED 2
1
2
3
4
O
N
STALL FORCE ADJUST
OPTIONS
MIN MAX MIN MAX OFF
<<< >>>
MODE 1
MODE 2
OPEN DIR.
SLV OPN
DUAL MODE
LOW BATT
ON
ON
>>>
SIMUL
SLAVE
SECURE
OFF
OFF
<<<
DELAY
MASTER
SAFE
1
2
3
4
O
N
STALL FORCE ADJUST
OPTIONS
<<< >>>
MODE 1
MODE 2
OPEN DIR.
SLV OPN
DUAL MODE
LOW BATT
ON
ON
>>>
SIMUL
SLAVE
SECURE
OFF
OFF
<<<
DELAY
MASTER
SAFE
1
2
3
4
O
N
STALL FORCE ADJUST
OPTIONS
MIN MAX MIN MAX OFF
<<< >>>
MODE 1
MODE 2
OPEN DIR.
SLV OPN
DUAL MODE
LOW BATT
ON
ON
>>>
SIMUL
SLAVE
SECURE
OFF
OFF
<<<
DELAY
MASTER
SAFE
1
2
3
4
O
N
STALL FORCE ADJUST
OPTIONS
MIN MAX MIN MAX OFF
<<< >>>
MODE 1
MODE 2
OPEN DIR.
SLV OPN
DUAL MODE
LOW BATT
ON
ON
>>>
SIMUL
SLAVE
SECURE
OFF
OFF
<<<
DELAY
MASTER
SAFE
Master DIP Switch
Settings
Slave DIP Switch
Settings
IMPORTANT: The #2 Switch Settings are set on the MASTER Operator only.
If DIP #3 is set to slave (ON), DIP #2 and #4 are dictated by MASTER DIP settings.
DIP #3
ON: SLAVE mode used for SLAVE operator only
OFF: MASTER mode used for MASTER operator only
DIP #4
ON: FAIL SECURE mode
OFF: FAIL SAFE mode
DIP #2
ON: SLAVE and MASTER open simultaneously
OFF: MASTER opens 1st, SLAVE delays when opening
DIP #1
OFF: For gate that opens to the left, closes to the right.
ON: For gate that opens to the right, closes to the left.