Yaskawa iQpump Controller User Manual - Manual (Page 64)

3.4 Drive Main Menu
64 YASKAWA TM.iQp.06 iQpump Controller User Manual
◆ Operation Menu (-DRIVE-)
This menu is used for setting a speed command or monitoring values such as output frequency and output current. It is also used for
displaying the fault history and the fault traces. The iQpump drive must be in this menu in order to run, see parameter b1-08.
■ U1 Monitor List
Follow the key operations below ( Figure 3.3 ) to access the Operation Menu:
Figure 3.3 U1 Monitor List Access Procedure
Use and keys to scroll through the U1 Monitor Parameter List. Refer to Parameters on page 165 for functional
description.
Table 3.8 U1 Monitor Parameter List
IMPORTANT
• Leaving the iQpump drive in a menu other than the Operation Menu, will prohibit the iQpump drive
from running. While running, if the iQpump drive is in a menu other than “Operation” and the run com-
mand is removed and re-applied, the iQpump drive will stop and will not start until the Operation Menu is
selected unless b1-08 = 1.
Monitor
Parameter Name
Digital Operator Display
Monitor
Parameter Name
Digital Operator Display
U1-01
Auto Setpoint Reference
Auto: Setpoint
U1-29
kWh
kWh Lo 4 Digits
U1-02
Output Frequency
Output Freq
U1-30
MWh
kWh Hi 5 Digits
U1-03
Output Current
Output Current
U1-34
First Parameter Causing an OPE
OPE Detected
U1-06
Output Voltage
Output Voltage
U1-36
PI Input
PI Input
U1-07
DC Bus Voltage
DC Bus Voltage
U1-37
PI Output
PI Output
U1-08
Output Power
Output kWatts
U1-38
PI Setpoint
PI Setpoint
U1-10
Input Terminal Status
Input Term Sts
U1-39
Memobus Communication Error Code
Transmit Err
U1-11
Output Terminal Status
Output Term Sts
U1-40
Heatsink Cooling Fan Operation Time
FAN Elapsed Time
U1-12
Drive Operation Status
Int Ctl Sts 1
U1-54
Network PI Feedback
Net PI Feedback
U1-13
Cumulative Operation Time
Elapsed Time
U1-55
Pump Network Status 1
PumpNet Status1
U1-14
Software Number
FLASH ID
U1-56
Pump Network Status 2
PumpNet Status2
U1-15
Terminal A1 Input Voltage
Term A1 Level
U1-57
Pump Network Status 3
PumpNet Status3
U1-16
Terminal A2 Input Voltage
Term A2 level
U1-58
Pump Network Status 4
PumpNet Status4
U1-18
Motor Secondary Current (Iq)
Mot SEC Current
U1-59
Pump Network Control 1
PumpNet Control1
U1-20
Output Frequency After Soft Start
SFS Output
U1-60
Pump Network Control 2
PumpNet Control2
U1-24
PI Feedback Value
PI Feedback
U1-62
Running Queue No
Running Queue No
U1-28
CPU Number
CPU ID
U1-63
Pump Running 1
Pump Running1
-DRIVE-
** Main Menu **
- - - - - - - - - - - - - -
Operation
-DRIVE- Rdy
Frequency Ref
U1- 01 = 0.00Hz
- - - - - - - - - - - - - - - - - - - -
U1-02= 0.00Hz
U1-03= 0.00A
x1
-DRIVE-
U1-02=
Auto Setpoint Ref
U1- 0.00PSI
60.00Hz
U1-91= 0.00PSI
Rdy
01 =